Bosch SRV 45T63 manuale
PDF manuale
·
28 pagine
Inglese
Manuale
Consulta qui gratuitamente il manuale per il Bosch SRV 45T63. Il manuale rientra nella categoria Lavastoviglie ed è stato valutato da 1 persone con una media di 8.3. Il manuale è disponibile nelle seguenti lingue: Inglese. Hai domande sul Bosch SRV 45T63 o hai bisogno di aiuto? Fai la tua domanda qui
Indice
- 9000 210 846 (9009)
- en Table of contents
- Read the “Installation” chapter to learn how to install and connect the appliance correctly.
- m Warning
- Knives and other utensils with sharp points must be placed in the cutlery basket with the points downwards or horizontally on the knife shelf *.
- * depending on model
- The description of the childproof lock is at the back in the envelope.
- * depending on model
- m Warning
- Children could become locked in the appliance (risk of suffocation) or find themselves in other dangerous situations.
- Therefore: Pull out the mains plug, sever and dispose of the power cord. Destroy the door lock so that the door can no longer be closed.
- Diagrams of the control panel and the interior of the appliance can be found in the envelope at the front.
- Individual positions are referred to in the text.
- (
- Main switch
- 0
- Door opener
- 8
- Timer programming *
- @
- Digital display
- H
- Additional options **
- P
- Display “Check water supply”
- X
- Salt refill indicator
- `
- Rinse aid refill indicator
- h
- Programme buttons **
- * depending on model
- ** Number depending on model
- 1"
- Top basket
- 1*
- Knife shelf *
- 12
- Top spray arm
- 1:
- Bottom spray arm
- 1B
- Dispenser for special salt
- 1J
- Filters
- 1R
- Cutlery basket
- 1Z
- Bottom basket
- 1b
- Lock for detergent dispenser
- 1j
- Dispenser for rinse aid
- 9"
- Detergent dispenser
- 9*
- Rating plate
- * depending on model
- To ensure good washing results, the dishwasher requires soft water, i.e. containing low amounts of lime, otherwise white limescale will be deposited on the utensils and inner container.
- Tap water above 9° Clarke must be softened. The water is softened with salt (regeneration salt) in the water softening system of the dishwasher.
- The setting and therefore the required amount of salt depends on the degree of hardness of your tap water (see table).
- The amount of salt dispensed can be set from ‹ to ˆ.
- Salt is not required at the set value ‹.
- Always refill with special salt immediately before switching on the appliance. This ensures that overrun special salt solution is immediately washed out and does not corrode the rinsing tank.
- The salt refill indicator X on the fascia is lit. It goes out as soon as a sufficiently high salt solution has formed.
- If the set value ‹ is displayed, do not add any salt because salt will not be used during operation of the appliance, the salt display is switched off. If the set values ‚ to ˆ are displayed, salt must be added.
- If combined detergents with a salt component are used, salt can usually be omitted up to a water hardness of 21° dH (37° fH, 26° Clarke, 3.7 mmol/l). If the water hardness is over 21° dH, special salt must be used.
- As soon as the salt refill indicator X on the fascia is lit, top up the salt.
- Depending on the washing frequency and the hardness setting, the regeneration salt may not have to be topped up for several months.
- If the salt refill indicator X is impaired (e. g. when using combined detergents containing salt component), it can be switched off.
- As soon as the rinse-aid refill indicator ` is lit on the fascia, there is still a rinse-aid reserve of 1–2 rinsing processes. Refill with rinse aid.
- The rinse aid is required for stain-free utensils and clear glasses. Use only rinse aid for domestic dishwashers.
- Combined detergents with rinse-aid component may be used up to a water hardness of 21° dH (37° fH, 26° Clarke, 3.7 mmol/l) only. If the water hardness is over 21° dH, rinse aid must be used.
- The rinse aid dispensing rate can be adjusted steplessly. The clear rinse controller was set to 4 at the factory.
- Do not change the position of the rinse aid control unless there are streaks (rotate towards –) or water stains (rotate towards +) on the utensils.
- If the rinse-aid refill indicator ` is impaired (e. g. when using combined detergents containing rinse aid component), it can be switched off.
- Aluminium and silver parts have a tendency to discolour and fade during the wash cycle. Even some types of glass (e.g. crystal glass objects) may turn cloudy after many wash cycles.
- Causes:
- Recommendation:
- Very small utensils should not be washed in the machine, as they may fall out of the baskets.
- To prevent water from dripping off the upper basket onto the utensils in the lower basket, it is recommended to empty the appliance from the bottom up.
- Hot utensils are sensitive to shock! Therefore, when the programme ends, leave the utensils to cool down in the dishwasher until they can be handled.
- Top basket 1"
- Bottom basket 1Z
- Tip
- Heavily soiled utensils (pans) should be placed in the bottom basket. The more powerful spray jet provides a better dishwashing result.
- You should always place cutlery unsorted with the points downwards.
- To prevent injuries, place long, pointed implements and knives on the knife shelf.
- * depending on model
- Long knives and other utensils can be arranged horizontally.
- You can remove the knife shelf to wash taller utensils.
- * depending on model
- The spikes can be folded down to improve arrangement of pans, bowls and glasses.
- * depending on model
- Light-weight plastic accessories, e.g. cups, lids, etc. can be held securely in the small accessories holder.
- * depending on model
- If required, the height of the upper utensils basket 1" can be adjusted to provide more space for tall utensils either in the upper or lower basket.
- Appliance height 81 cm
- Top basket
- Bottom basket
- Setting 1 max. ø
- 20 cm
- 28 cm
- Setting 2 max. ø
- 25 cm
- 23.5 cm
- Select one of the two following procedures according to the design of the top basket for your appliance model:
- You can use tablets as well as powder or liquid detergents for dishwashers, but never use washing up liquid. The dosage can be individually adjusted with powder or a liquid detergent according to the degree of soiling. Tablets contain an adequately l...
- Note
- To ensure a good washing result, always follow the instructions on the detergent packaging!
- If you have further questions, we recommend that you contact the detergent manufacturers’ helpline.
- m Warning
- Read and observe the safety information and instructions for use on the packaging for cleaning and rinsing agents.
- Tip
- If the utensils are only lightly soiled, slightly less than the indicated amount of detergent is usually adequate.
- Suitable detergents and care products can be purchased online via our website or via customer service (see back page).
- Apart from conventional detergents (Solo), a number of products are offered with additional functions. These products contain not only the detergent but also rinse-aid and salt replacement substances (3in1) and, depending on the combination (4in1, 5i...
- As soon as combined detergents are used, the rinse programme is adjusted automatically to ensure the best possible rinsing and drying result.
- The max. possible number of programmes is illustrated in this overview. The corresponding programmes and their arrangement can be found on the fascia.
- Type of utensils
- Type of soiling
- Programme
- Possible additional options
- Programme sequence
- pots and pans, non-sensitive utensils and cutlery
- very adhesive burned- in or dried-on food remnants containing starch or protein
- ²
- Intensive 70°
- all
- Prerinse
- Clean 70°
- Intermediate rinse
- Final rinse 70°
- Dry
- Ò
- Auto 55°–65°
- Is optimised according to the soiling with the aid of sensors.
- mixed utensils and cutlery
- part dried, common household food remnants
- â
- Eco 50°
- Prerinse
- Clean 50°
- Intermediate rinse
- Final rinse 65°
- Dry
- sensitive utensils, cutlery, temperature- sensitive plastic and glasses
- slightly adhesive, fresh food remnants
- ê
- Gentle 40°
- Reduce Time
- Half load
- Prerinse
- Clean 40°
- Intermediate rinse
- Final rinse 55°
- Dry
- ò
- Quick 45°
- none
- Clean 45°
- Intermediate rinse
- Final rinse 55°
- all types of utensils
- cold rinsing, intermediate cleaning
- ú
- Prerinse
- none
- Prerinse
- You can select a suitable programme according to the type of utensils and degree of soiling.
- Test institutes can request the conditions for running comparison tests by sending an e-mail to
- dishwasher@test-appliances.com.
- Quote the appliance number (ENr.) and the production date (FD) which you can find on the rating plate 9* on the appliance door.
- * depending on model
- Additional options can be set with the buttons H.
- The >>Express Wash/ Speed Perfect<< function can reduce the running time by approx. 20% to 50% depending on the selected rinse programme. The change in the running time is indicated on the digital display @. To obtain optimum cleaning results at a re...
- If you have only a few items to wash (e.g. glasses, cups, plates), you can switch to “half load”. This will save water, energy and time. It is recommended to put a little less detergent in the detergent dispenser than for a full load.
- The programme data (consumption values) can be found in the summary of instructions. They refer to normal conditions and the water hardness set value …. Different influencing factors such as water temperature or line pressure may result in deviations.
- * depending on model
- The Aqua sensor is an optical measuring device (light barrier) which measures the turbidity of the rinsing water.
- The Aqua sensor is used according to the programme. If the Aqua sensor is active, “clean” rinsing water can be transferred to the next rinse bath and water consumption can be reduced by 2–4 litres. If the turbidity is greater, the water is drai...
- * depending on model
- While the programme is running, a light spot shines on the floor under the appliance door. Do not open the dishwasher door until the light point is no longer visible on the floor.
- If the appliance is installed at eye-level, with flush furniture front, the light point is not visible.
- When the programme is selected, the remaining running time of the programme is indicated on the digital display @.
- The running time is determined during the programme by the water temperature, the number of utensils as well as the degree of soiling and may vary (depending on the selected programme).
- * depending on model
- You can delay the start of the programme in 1 hour steps up to 19 hours.
- The programme has ended when the value ‹ is indicated on the numerical display @.
- The end of the programme is also indicated by an acoustic signal. This function can be changed as follows:
- Short time after the end of the programme:
- m Warning
- At the end of the programme please open the door fully and not partially when emptying the dishwasher. Any escaping water vapour could damage sensitive worktops.
- After you have switched the appliance on, it is possible to change the programme within 2 min.
- If you want to change the programme afterwards, the appliance waits until the initiated programme section (e. g. washing) ends. The remaining time comprises the remaining time of the previous programme section and the remaining time of the new select...
- The final rinse uses a higher temperature which improves the drying result. The running time may increase slightly. (Caution if utensils are delicate!)
- A regular inspection and maintenance of your machine will help to prevent faults. This saves time and prevents problems.
- If you find such deposits:
- Clean the appliance with detergents/ appliance cleaners which are particularly suitable for use with dishwashers.
- Never use a steam cleaner to clean your dishwasher. The manufacturer is not liable for any consequential damage.
- Regularly wipe the front of the appliance and fascia with a damp cloth; water and a little washing up liquid are adequate. Do not use sponges with a rough surface or abrasive detergents, as these could scratch the surfaces.
- Stainless steel appliances: To prevent corrosion, avoid using sponge cloths or wash them out thoroughly several times before using for the first time.
- m Warning
- Never use other chlorinated household detergents! Health hazard!
- The filters 1J keep large foreign objects in the rinsing water away from the pump. These foreign objects may occasionally block the filters.
- Limescale and contaminants in the rinsing water may block nozzles and bearings on the spray arms 12 and 1:.
- The majority of faults which could occur in daily operation can be rectified by the user. This ensures that the appliance is quickly available for use again. The following overview will help you locating the causes and gives helpful advise to elimina...
- Note
- If the appliance stops during dishwashing or does not start for no obvious reason, first run the Abort programme function (Reset).
- (See chapter entitled “Dishwashing”)
- m Warning
- Don’t forget: Repairs may be carried out by technicians only. If a component has to be replaced, ensure that only original spare parts are used. Improper repairs or use of non-original spare parts may cause considerable damage and put the user at c...
- Large food remnants in the rinsing water not retained by the filters may block the waste water pump. The rinsing water is then not pumped out and covers the filter.
- In this case:
- If phosphate-free detergents are used with hard tap water, white deposits may be deposited more easily on utensils and the container walls.
- Contact the detergent manufacturer, in particular if:
- If the advice given does not resolve your problem, please contact your customer service. Contact details can be found on the back cover of this instruction manual or in the enclosed customer service list. When calling , please quote the appliance num...
- Rely on the expertise of the manufacturer. Call us to ensure that the repair will be carried out by fully-trained service engineers, who are equipped with original spare parts for your appliance.
- The dishwasher must be connected correctly, otherwise it will not function properly. The specifications for the inlet and outlet as well as the electrical connected loads must correspond with the required criteria as specified in the following paragr...
- Install the appliance in the correct sequence:
- m Warning
- If the appliance is not in a cavity and a side panel is accessible, the door hinge area must be covered at the side for reasons of safety (risk of injury). The covers are available as optional accessories from customer service or specialist outlets.
- Your dishwasher has been checked thoroughly in the factory to ensure that it is in working order. This may cause small water stains. These will disappear after the first wash cycle.
- Weight:
- max. 53 kg
- Voltage:
- 230 V, 50 Hz
- Connected load:
- 2,3 kW
- Fuse:
- 10/13 A
- Water pressure:
- at least 0.05 MPa (0.5 bar), maximum 1 MPa (10 bar). At a higher water pressure: connect pressure-reducing valve ahead.
- Inlet rate:
- minimum 10 litres/minute
- Water temperature:
- cold water; hot water max. temperature 60 °C.
- The required installation dimensions can be found in the installation instructions. Level the appliance with the aid of the height-adjustable feet. Ensure that the appliance is situated securely on the floor.
- Also observe the sequence of worksteps here.
- Empty the dishwasher and secure loose parts.
- Transport appliance upright only.
- (This prevents residual water from running into the machine control and damaging the programme sequence.)
- If the appliance is in a room where there is a risk of frost (e.g. holiday home), empty the appliance completely (see Transportation).
- Both the packaging of new appliances and the old appliances themselves contain valuable raw materials and recyclable materials.
- Please dispose of the individual parts separated according to type.
- Please ask your dealer or inquire at your local authority about current means of disposal.
- All plastic parts of the appliance are identified with internationally standardised abbreviations (e.g. >PS< polystyrene). Therefore, plastic waste can be sorted out when the appliance is being disposed of.
- Please follow the safety instructions under “Delivery”.
- Please follow the safety instructions under “Disposal of your appliance”.
- This appliance is identified according to the European guideline 2002/96/EC on waste electrical and electronic equipment – WEEE. The guideline specifies the framework for an EU-wide valid return and re-use of old appliances.
- 9000 210 846 (9009)
Specifiche Bosch SRV 45T63
Di seguito troverai le specifiche del prodotto e le specifiche del manuale di Bosch SRV 45T63.
Generale
| Marca | Bosch |
| Modello | SRV 45T63 |
| Prodotto | Lavastoviglie |
| Lingua | Inglese |
| Tipo di file | Manuale d'uso (PDF) |
Domande frequenti
Non riesci a trovare la risposta alla tua domanda nel manuale? Puoi trovare la risposta alla tua domanda nelle FAQ sul Bosch SRV 45T63 che trovi di seguito.
Cosa devo fare con una lavastoviglie puzzolente?
Si deve risciacquare i piatti?
Quanto detersivo per piatti devo usare?
Come si riempie il sale ammorbidente nella lavastoviglie?
Il manuale del Bosch SRV 45T63 è disponibile in Italiano?
La tua domanda non è elencata? Fai la tua domanda qui
Nessun risultato
Ho bisogno di aiuto?
Hai una domanda relativa a Bosch SRV 45T63 e la risposta non è nel manuale? Fai qui la tua domanda Fornisci una descrizione chiara e completa del problema e della tua domanda. Migliore sarà la descrizione del tuo problema e della domanda, più facile sarà per gli altri proprietari di Bosch SRV 45T63 fornirti una buona risposta.
Numero di domande: 0