Brother PT-1230PC

Brother PT-1230PC manuale

    Thank you for choosing the PT-1230PC. Your new P-touch labeler uses P-touch Editor Lite software, which is already installed on your labeler.
    There is no need to install any software or drivers onto your PC in order to make creative labels. This manual includes important precautionary
    information and simple instructions for operating your new P-touch labeler. Be sure to read the instructions before use and use the product in ac-
    cordance with these instructions. Keep this manual handy for future reference.
    Federal Communications Commission (FCC) Declaration of Conformity (For USA Only)
    Responsible Party: Brother International Corporation 100 Somerset Corporate Boulevard Bridgewater, NJ 08807-0911 USA
    TEL: (908) 704-1700
    declares that the product: Product Name: P-touch Labeler PT-1230PC
    Model Number: PT-1230PC
    This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful
    interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
    This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
    limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and
    can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
    communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
    interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to cor-
    rect the interference by one or more of the following measures:
    Reorient or relocate the receiving antenna.
    Increase the separation between the equipment and receiver.
    Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
    Consult the dealer or an experienced radio/TV technician for help.
    Changes or modi cations not expressly approved by Brother Industries, Ltd. could void the user’s authority to operate the equipment.
    The enclosed interface cable should be used in order to ensure compliance with the limits for a Class B digital device.
    General Precautions
    Always use the speci ed voltage and the suggested AC adapter (AD-24) for this machine to prevent any damage or failure.
    Unplug the power cord immediately and stop using the P-touch labeler during an electrical storm. There may be a remote risk of electric shock from lightning.
    Do not use the AC adapter in places of high humidity such as bathrooms.
    Do not overload the power cord.
    • Do not place heavy objects on, or damage the power cord or plug. Do not forcibly bend or pull the power cord. When disconnecting the power cord from the power outlet, al-
    ways hold the plug.
    • To prevent re or electric shock, make sure that the plug is fully inserted to the power outlet. Do not use an outlet that is loose.
    Do not get the machine/AC adapter/power plug wet, such as by handling them with wet hands or spilling beverages on to them.
    Do not disassemble or modify P-touch labeler/AC adapter/batteries.
    Do not use metallic articles, such as tweezers or a metallic pen, when exchanging the batteries.
    Do not throw into re or heat up the battery.
    Disconnect the AC adapter, remove batteries and stop using immediately if you notice any abnormal odor, heat, discoloration, deformation or anything unusual while in use, or
    in storage.
    To avoid injuries, do not touch the blade of the cutter unit or any metal parts near the print head.
    Do not apply excessive pressure to the cutter lever.
    Remove the batteries and disconnect the AC adapter if you do not intend to use P-touch labeler for an extended period of time.
    • Do not use old and new batteries together or mix alkaline batteries with other type batteries, or set the positive and negative end in the wrong position. Otherwise, the batter-
    ies may leak or be damaged.
    To prevent damage or breakage, do not drop or hit P-touch labeler/AC adapter.
    Use only the USB cable included with the P-touch labeler.
    • Depending on the location, material, and environmental conditions, the label may unpeel or become irremovable, the color of the label may change or be transferred to other
    objects. Before applying the label, check the environmental condition and the material.
    Do not use the P-touch labeler in any way or for any purpose not described in this guide. Doing so may result in accidents or damage the machine.
    Use only Brother TZ tapes with this machine. Do not use tapes that do not have the
    Do not clean P-touch labeler with alcohol or other organic solvents. Only use a soft, dry cloth.
    Do not touch the print head with your ngers anytime to prevent from a burn. Use a soft wipe (e.g. a cotton swab) when cleaning the print head.
    Do not put any foreign objects into the tape exit slot or AC adapter connector, etc.
    Do not place the P-touch labeler/battery in direct sunlight or rain, near heaters or other hot appliances, in any location exposed to extremely high or low temperatures (e.g. on
    the dashboard or in the back of your car), high humidity, or dusty locations.
    Do not try to print labels using an empty tape cassette in the P-touch labeler. Doing so will damage the print head.
    Do not pull the tape being fed from the P-touch labeler, otherwise the tape cassette or P-touch labeler may be damaged.
    Open the cassette
    Insert a tape
    Close the cassette
    Verify that the P-touch labeler is
    turned off. Open the cassette cover
    as shown by the arrow in the above
    illustration while pressing the part
    marked "<<".
    Insert a TZ tape cassette as shown
    in the above illustration.
    Make sure that the end of the tape feeds under the tape
    If the ink ribbon is loose, use your nger to wind the toothed
    wheel in the direction of the arrow on the cassette.
    Use only Brother TZ tapes with the P-touch labeler.
    For initial use of the tape, install the tape, press and hold the
    power/feed button to feed the tape. Then, push in the tape cut-
    ter lever to cut the tape.
    Connect the P-touch labeler's power supply.
    Insert six new AAA alkaline batteries (LR03),
    making sure that their poles point in the
    correct directions. Always replace all six
    batteries at the same time using brand new
    Auto Power Off Function
    When the P-touch labeler is operating on battery power only,
    it will turn off automatically if not used for a period of 20 min-
    utes. The message “Unsafe Removal of Device” may be
    displayed depending on the Operating System running on
    your PC. Any data being displayed will be saved. When you
    turn the labeler back on, click on the Editor Lite icon to re-
    sume creating your label.
    Connect the USB cable and start P-touch Editor Lite.
    Download and install the PT-1230PC’s
    driver and P-touch Editor 5.0 from Broth-
    ers website. Connect the P-touch labeler
    to your PC when requested during this
    For more information about install-
    ing the software, visit http://solu-
    If you would like to use the more advanced software that is available for your P-touch labeler,
    you are able to download P-touch Editor 5.0 from the Brother web site. This advanced soft-
    ware will give you greater label making functionality.
    Do not connect the P-touch labeler to your PC before you begin the P-touch Edi-
    tor 5.0 installation.
    Starting P-touch Editor 5.0
    P-touch Editor 5.0.
    Double-click the short-
    cut icon on the desktop
    (P-touch Editor 5.0).
    Click P-touch Editor 5.0
    under All Programs on
    the Start menu.
    P-touch Editor 5.0.
    If you have trouble using
    the software, refer to the
    help information available
    in P-touch Editor 5.0.
    Getting Ready
    Review the names of P-touch labeler parts.
    Install a TZ tape cassette.
    The PT-1230PC has 2 mode selector settings - “EL” and “E”. The mode
    selector switch is pre-set at the factory to the EL mode, for use with
    P-touch Editor Lite. For E mode, you need to download P-touch Editor 5.0
    and the required drivers. For details on how to download the P-touch Edi-
    tor 5.0, see “Starting P-touch Editor 5.0” below.
    Connect the
    USB cable.
    Turn on the P-touch labeler.
    The LED lamp will light up.
    XP User
    2000 User
    Windows Vista
    Go to My Computer and open Removable Disk, then start
    P-touch Editor Lite by double-clicking
    Pop-up Window
    Appears. Select
    P-touch Editor Lite
    and click OK.
    Pop-up Window
    Appears. Click
    P-touch Editor
    It will take longer than usu-
    al to start P-touch Editor
    Lite when connecting P-touch
    labeler to your computer for the
    first time. If the software does
    not start automatically when you
    connect the machine, you may
    launch it from My Computer.
    Start P-touch Editor Lite by dou-
    For details on using
    P-touch Editor Lite,
    see the back of this
    P-touch Editor Lite
    starts immediately.
    *Microsoft Windows and Windows Vista are registered trademarks of Microsoft Corporation in the United States and other
    *The name of other software or products used in this document are trademarks or registered trademarks of the respective
    companies that developed them.
    When using the optional AC adapt-
    er (AD-24), insert the plug on the
    adapter cord into the adapter jack
    on the bottom end of the P-touch
    labeler. Insert the plug into the
    nearest standard electrical outlet.
    Move the mode selector
    switch on the back of the
    P-touch labeler to the “E”
    position before connect-
    ing the USB cable.
    Do not turn off the power or remove the labeler while
    using P-touch Editor Lite.
    How to disconnect the P-touch
    Exit P-touch Editor Lite by clicking on the at the top
    To disconnect the labeler, click the icon in the computers
    task bar (
    , , or ).
    Click Safely remove USB Mass Storage Device.
    When The device can be safely removed is displayed,
    turn off the P-touch labeler and disconnect the USB ca-
    LED lamp
    Tape cutter
    Tape exit slot
    AC adapter(optional)
    Mode selector
    USB port
    Print head
    Tape cutter
    Printed in China
    When using
    Windows Vista
    When connecting the device for the rst time, perform the
    scan and then select the Always do this for software and
    games check box on the dialog box displayed when the
    scan completes. P-touch Editor Lite will start automatically
    the next time you connect the P-touch labeler.
Brother PT-1230PC

Ho bisogno di aiuto?

Numero di domande: 0

Hai domande sul Brother PT-1230PC o hai bisogno di aiuto? Fai qui la tua domanda. Fornisci una descrizione chiara e completa del problema e della domanda. Più dettagli fornisci per il tuo problema e la tua domanda, più facile sarà per gli altri proprietari di Brother PT-1230PC rispondere correttamente alla tua domanda.

Consulta qui gratuitamente il manuale per il Brother PT-1230PC. Il manuale rientra nella categoria Macchina etichettatrice ed è stato valutato da 1 persone con una media di 7.9. Il manuale è disponibile nelle seguenti lingue: Inglese. Hai domande sul Brother PT-1230PC o hai bisogno di aiuto? Fai la tua domanda qui

Specifiche Brother PT-1230PC

Marca Brother
Modello PT-1230PC
Prodotto Macchine etichettatrici
EAN 4977766660013, 4977766660037
Lingua Inglese
Tipo di file PDF
Velocità di stampa
A colori
Risoluzione massima 180 x 180
Velocità di stampa 10
Interfaccia standard USB
Quantità porte USB 1.1 1
Tecnologia di connessione Con cavo e senza cavo
Requisiti di sistema
Sistema operativo compatibile Windows 2000 Professional/XP/Vista
Altre caratteristiche
Dimensioni (LxPxA) 53 x 158 x 112
Dimensioni e peso
Peso 400
Larghezza carta supportata 3.5, 6, 9, 12
Gestione energetica
Tipo batteria Stilo AA
Tecnologia batteria Alcali✗
Numero di batterie 6

Domande frequenti

Di seguito, troverai le domande più frequenti riguardo Brother PT-1230PC .

La tua domanda non è elencata? Fai la tua domanda qui


Stai cercando un manuale? ManualeD' farà in modo che tu possa trovare il manuale che stai cercando in un attimo. Il nostro database contiene più di 1 milione di manuali in formato PDF di oltre 10.000 marchi. Ogni giorno aggiungiamo i manuali più recenti in modo che sia sempre possibile trovare il prodotto che stai cercando. È molto semplice: basta digitare il marchio e il tipo di prodotto nella barra di ricerca e immediatamente visualizzerai gratuitamente il manuale di tua scelta online.


© Copyright 2020 ManualeD' Tutti I diritti riservati.

Utilizziamo i cookie per essere sicuri che tu possa avere la migliore esperienza sul nostro sito. Se continui ad utilizzare questo sito noi assumiamo che tu ne sia felice.

Leggi di più