Draper 253219 projection screen 253219 manuale

Draper 253219 projection screen 253219
7.6 · 1
PDF manuale
 · 2 pagine
Inglese
manualeDraper 253219 projection screen 253219

Onyx by Draper

Page 2 of 2

Figure 8

Mounting Screen to Wall

Determine height at which screen is to be mounted.
Please Note: Top edge of screen frame will be located 1.5"above mounting
bracket hole centerline when mounted to wall.
Mark hole centerline so that both Z-brackets can be mounted parallel and
at equal height.
Install Z-brackets so that the outermost edges are safely within the overall
length of the aluminum frame extrusion to allow for minor horizontal screen
adjustments. Installer is responsible for providing attachment hardware.
Position screen slightly above Z-brackets on wall (see Fig. 10).

Surface to Frame Assembly

Return frame onto clean surface, face down, and drape completed surface
assembly over completed frame profi le with rounded edge of surface
retention extrusion visible.
Insert any side of surface to notch #1 on corresponding side of frame
extrusion (see Fig. 8).
Insert opposite side of surface to notch #1 of frame extrusion.
Repeat steps 2-3 with remaining edges of surface.
Ensure surface retention extrusions are centered lengthwise in tension
slots on all 4 edges of surface.
If additional tension is desired or required over time, adjust surface one
edge at a time to tension notch #2.
Please Note: It is not necessary to adjust more than one edge at a time to
increase surface tension.
Z-brackets
supplied with
screen. Installer is
responsible for
ensuring appropriate
screws/bolts are used.
Wall
Figure 10
Lower screen until it engages over Z-brackets. Center screen horizontally
on brackets as necessary.
Please Note: Make sure screen is installed level.
Figure 6

Surface Preparation

Move frame assembly out of the way, unroll viewing surface and place on
smooth/clean surface. (Orient viewing surface so that folded side of hem is
visible.)
Insert plastic tubing inside pocket formed by hem on all 4 edges of viewing
surface (see Fig. 6).
Carefully slide surface retention extrusion (rounded edge visible) along
hem and onto surface on all 4 edges of fabric (see Fig. 7).
Caution: Do
not allow fabric to snag on end of extrusion. If the screen
fabric is not parallel with the surface retention extrusion, then
it may slit and tear during installation.
Please Note: To make this step easier, pinch the end of the pocket closed
before sliding it into the surface retention extrusion.
Figure 7
Surface retention extrusion should extend beyond edge of viewing surface
equally at both ends.
Verify that all surface retention extrusions are installed with rounded edge
visible and are centered on surface material.
Plastic Tubing
Surface Retention
Extrusion
Back of
Viewing Surface
Back of
Viewing Surface
Surface
Retention
Extrusion
Fabric Attachment Extrusions
Viewing
Surface

Onyx (Exploded Rear View)

1
5
/
8
"
4"

Onyx Frame

—Side Detail*

*Viewing surface is approximately ¼" from wall.
www.draperinc.com
(765) 987-799
9

Corner Reinforcement

If screen is being fl own (suspended), raised and lowered by a TorkStar, or if
screen is 12' (viewing area) or larger in overall height or width, install
Corner reinforcement Gussets to all four corners (see Fig. 9)
Figure 9

Consulta qui gratuitamente il manuale per il Draper 253219 projection screen 253219. Il manuale rientra nella categoria Schermi per proiettori ed è stato valutato da 1 persone con una media di 7.6. Il manuale è disponibile nelle seguenti lingue: Inglese. Hai domande sul Draper 253219 projection screen 253219 o hai bisogno di aiuto? Fai la tua domanda qui

Ho bisogno di aiuto?

Hai una domanda relativa a Draper e la risposta non è nel manuale? Fai qui la tua domanda Fornisci una descrizione chiara e completa del problema e della tua domanda. Migliore sarà la descrizione del tuo problema e della domanda, più facile sarà per gli altri proprietari di Draper fornirti una buona risposta.

Numero di domande: 0

Generale
Draper
253219 projection screen 253219 | 253219
Schermo per proiettore
641092150985, 0641092150985
Inglese
Manuale d'uso (PDF)
Prestazione
Rapporto d'aspetto nativo16:9
Ampiezza dello schermo visibile (L)3556 mm
Altezza dello schermo visibile (A)2032 mm
Dimensione totale dello scermo (Altezza x Ampiezza)2235 x 3759 cm
Diagonale161 "
FormatoHDTV
Design
Bordi101.6 mm
Colore del prodottoBlack,White
Dimensioni e peso
Peso29480 g
Mostra di più

Non riesci a trovare la risposta alla tua domanda nel manuale? Puoi trovare la risposta alla tua domanda nelle FAQ sul Draper 253219 projection screen 253219 che trovi di seguito.

La tua domanda non è elencata? Fai la tua domanda qui

Nessun risultato