Draper Cineperm manuale

Draper Cineperm
9.5 · 1
PDF manuale
 · 1 pagina
Inglese
manualeDraper Cineperm

Installation Instructions

Cineperm Permanently Tensioned Projection Screen by Draper

Copyright © 2011 Draper Inc. Form Cineperm_Inst11 Printed in U.S.A.
Frame Assembly
Standard Frame—
Lay out frame pieces on fl oor, by matching up color-coded tape near
corners. Snaps should be facing up.
Assemble frame (see Fig. 1). If nec es sary gently tap frame ends with a
rubber mallet to make sure castings are fully seated.
Surface Installation
Carefully remove surface from cardboard tube and unroll onto a clean
cloth or paper.
Engage snaps in each corner, then secure rest of screen snaps.
Stretch fabric across frame. Use extreme caution when attaching fabric.
Overstretching or rough handling could cause the viewing surface to tear.
Frame Installation (Standard Frame)
Outside (Face) Mount—
Drill mounting holes in frame (see Fig. 2).
Mark wall and drill holes to correspond with those in the frame.
Enlarge holes in frame side furthest from wall to allow screw heads to pass
through (see Fig. 2). Do not allow screw heads to remain outside the
frame: overtightening could bend frame and affect screen fl atness.
Cineperm
frame
Mounting hardware
by others
Viewing surface snaps to
frame, covering mounting holes
Supporting structure
Drill through frame for
mounting hardware.
Enlarge first hole for screw
head to pass through.
Figure 2
Figure 3
Inside (Jamb) Mount—
Place frame assembly in opening to check for a snug fi t. If frame is too
large, opening may have to be enlarged. If frame is too small or does not
sit square in the opening, shims and caulking may be required.
Drill mounting holes in frame, and enlarge the fi rst holes to allow screw
heads to pass through (see Fig. 3). Do not allow screw heads to remain
outside the frame: overtightening could bend frame and affect screen
atness.
Drill holes in jamb.
Attach frame using appropriate fasteners for mounting surface (provided
by others).
Use caulk to ensure there is no light leakage around edges of frame.
Truss Frame—
Unfold and lay out pieces on fl oor, by matching up color coded marks.
Lock all hinges (see Fig. 1). Stage Left and Stage Right sections should be
placed with snaps up. Top and bottom sections should be placed with
snaps down.
To increase frame rigidity, hinges on top and bottom sections have rivnuts
marked with red and green. Insert a Handy Crank through the threadless
rivnut (red) and tighten into the threaded rivnut (green).
Apply small sections marked “Stiffener Bars” to back of bottom frame
section, using 8 Handy Cranks. These eliminate sag on large suspended
frames. Failure to use all Handy Cranks may result in screen frame
damage. Turn bottom frame section over so snaps face up.
Repeat step 3 for top frame section.
Join top and bottom sections to Stage Left and Stage Right, using 2
Handy Cranks on each of the 4 corners. Match numbers on white labels.
NOTE: No Handy Crank should protrude outside screen frame.
Attach surface (see “Surface Installation”), and suspend using appropriate
materials (provided by others to meet specifi c installation requirements).
Opening
Wall
Anchor bolt by others.
Clearance hole in outer
wall by others.
Snap-on viewing surface
1" square
alum. tube
Wall
Anchor bolt by others.
Clearance wall in outer
wall by others.
Locate between snaps.
1 square
alum. tube
Snap-on viewing surface
Inside (Jamb) Mount
Outside (Face) Mount
Attach frame to wall using appropriate fasteners for mounting surface
(provided by others).
NOTE: Measure screen frame width at the top, bottom, and center; Make
sure the frame is installed so the center width is same as the width at
the top and bottom.
Figure 1
Standard Frame
Truss Style Frame
Caution
Read instructions through completely before pro ceed ing.
Follow instructions carefully. Installation con trary to instructions
invalidates warranty.
Bent or warped frames will affect surface fl atness and image quality.
Screen should be square, and width should not vary from the center to
the ends of the frame
When lifting assembled screen, do not lift at only one corner; lift at both
corners. Lifting by one corner could result in damage to the screen
frame, especially on large screens.
Screen should be installed level (using a carpenter’s level).
Nothing should be fastened to screen frame or viewing surface.
Be careful not to rip screen material when attaching surface to frame.
The ideal temperature range for assembling this screen to prevent
damaging the surface is 68°-78° F (20°-26° C). Assembling below
recommended temperatures may damage surface and void warranty.
NOTE: Screen has been inspected and tested at factory prior to shipment.
Jamb of opening
Viewing Surface snaps to
frame, covering mounting holes
Cineperm
frame
Drill through frame for
mounting hardware. Enlarge
first hole for screw head
to pass through.
Mounting hardware
by others
Color-coded
tape
®
Handy
Cranks
If you encounter any diffi culties installing or servicing your Cineperm, call your
dealer or Draper, Inc. in Spiceland, In di ana, 765-987-7999, or fax 765-987-7142.
Always fold viewing surface with snaps face-to-face.
Do not permit screen fabric to contact border material
or snaps when folded. Store in pouch provided.

Consulta qui gratuitamente il manuale per il Draper Cineperm. Il manuale rientra nella categoria Schermi per proiettori ed è stato valutato da 1 persone con una media di 9.5. Il manuale è disponibile nelle seguenti lingue: Inglese. Hai domande sul Draper Cineperm o hai bisogno di aiuto? Fai la tua domanda qui

Ho bisogno di aiuto?

Hai una domanda relativa a Draper e la risposta non è nel manuale? Fai qui la tua domanda Fornisci una descrizione chiara e completa del problema e della tua domanda. Migliore sarà la descrizione del tuo problema e della domanda, più facile sarà per gli altri proprietari di Draper fornirti una buona risposta.

Numero di domande: 0

Generale
Draper
Cineperm | 250013
Schermo per proiettore
641092147220, 6410921472208, 0641092147220
Inglese
Manuale d'uso (PDF)
Prestazione
Rapporto d'aspetto nativo4:3
Dimensione totale dello scermo (Altezza x Ampiezza)137 x 183 cm
Diagonale90 "
Dimensioni e peso
Peso9979 g
Mostra di più

Non riesci a trovare la risposta alla tua domanda nel manuale? Puoi trovare la risposta alla tua domanda nelle FAQ sul Draper Cineperm che trovi di seguito.

La tua domanda non è elencata? Fai la tua domanda qui

Nessun risultato