Draper Envoy manuale

Draper Envoy
7.4 · 1
PDF manuale
 · 3 pagine
Inglese
manualeDraper Envoy
Copyright © 2013 Draper Inc. Form Envoy_Inst13 Printed in U.S.A.

Installation/Operating Instructions

Envoy Electric Projection Screen by Draper

Hanging Screen
General:
When locating viewing surface and checking clearance for screen’s operation,
remember surface is centered in case. Screen is normally recessed above ceiling
and may be installed in a varie ty of ways. See typical installation detailed on page
2. Regardless of mounting method used, the following points apply:
1 Screen should be lifted into position only by the end mounting brackets.
Keep case level by lifting end plates simultaneously to prevent surface
damage. Draper provides eyebolts to use in hoisting the screen. Never
attempt to lift screen along its length.
2 Screen should be positively and securely supported so that vibration or even
abusive pulling on viewing surface will not weaken installation.
3 Installer must insure that fasteners used are of adequate strength and suitable
for the mounting surface chosen.
4 Entire bottom of case must be readily accessible after installation is complete.
5 Hinge on bottom board and particularly hinge on automatic trap door of screen
must be permitted to operate freely. Front and back of case must be straight—
not forced to warp or bow. Hinges must be free from mastic or paint buildup,
and doors must be unobstructed by ceiling tiles.
6 Do not use screen case to support adjacent sections of ceiling.
7 If trim pieces must be attached to case, do not permit screws to pro trude
through ¾" wall of case. Do not attach trim with nails.
8 If case is painted, slots around doors should be shielded to protect viewing
surface from paint splatters or overspray.
9 Do not seal unit in ceiling unit electrical connections have been made and
screen has been operated successfully.
Caution
1 Read instructions through completely before proceeding.
2 Follow instructions carefully. Installation contrary to instructions invalidates
warranty.
3 Do not lift case in center. Lift the ends simultaneously to avoid damage
to case and surface.
4 Before removing screen from crate, check for damage and to make sure
all parts are included.
5 Entire bottom of screen case should be unobstructed to permit proper
operation of automatic trap door, and access to bottom panel for making
electrical connections or servicing.
6 Screen should be installed level (using a carpenter’s level).
7 Nothing should be fastened to screen dowel, viewing surface or auto matic
trap door.
8 Operating switch(es) packed separately in screen carton. Do not discard with
packing material.
9 Screen operates on 110-120V, 60 hz., 1.1 amp current draw.
NOTE: Screen has been thoroughly inspected and tested at factory and found
to be operating properly prior to shipment.
Electrical Connections
Screen operates on 110-120V, 60 hz., 1.1 amp current draw.
Junction box is located just above bottom board near left end of screen. Bottom
board is held closed with flathead screws and may be opened with a Phillips
screwdriver. Automatic trap door is held shut by viewing surface and must not be
forced open. Removal of junction box cover plate exposes red, black and white
pigtail leads and green internal ground wire per wiring diagram attached.
Screen is shipped with internal wiring complete and control switch(es) fully boxed.
Wire connecting screen to switch(es) and switch(es) to power supply should be
furnished by installer. Connections should be made in accordance with attached
wiring diagram, and wiring should comply with National and local electrical codes.
All operating switches should be “off before power is connected.
Operation
When screen is first operated, be cautious! If automatic trap door does not drop
open immediately when switch is flipped “down”, return switch to “off and free trap
door and/or recheck electrical connections before proceeding. Cycle unit down and
up several times to confirm satisfactory operation.
110-120V Single Station Control — 3-position up-off-down switch permits
operation to be stopped at any point. Factory adjusted limit switches automatically
stop screen when fully down or fully up.
110-120V Multiple Station Control—Switches are similar in appearance to
110-120v Single Station Control. Screen stops when switch is released and
may be restarted in either direction. Factory adjusted limit switches stop screen
Limit Adjustments (Standard & Standard Quiet Motors)
Please Note: Screen limits are factory set for optimum performance of the
screen. A procedure is outlined below for minor tweaks, but any adjustment
of these limits may negatively affect the flatness of the screen surface and
could also void the warranty. Please check with Draper prior to resetting
screen limits.
CAUTION: Always be prepared to shut screen off manually when new
adjustment is being tested. Screen may be severely damaged if viewing
surface is allowed to run too far up or too far down.
CAUTION: Be sure all switches are in “off” position before adjusting limit
switches.
Tools needed: Flashlight, small flathead screwdriver/Allen wrench (4mm or
5
/
32
").
The motor limit screws are normally located on the audience left of screen roller.
"DOWN" LIMIT ADJUSTMENT
To Reduce Screen Drop
1 Raise screen surface about 1' above desired setting and turn off.
2 Turn WHITE/DOWN limit screw clockwise (3 screw turns = ½ roller revolution).
3 Test by running screen down and repeat steps 1 and 2 until desired position is
reached.
To Increase Screen Drop
1 Run screen to the down limit.
2 With the down switch on, turn the WHITE/DOWN limit screw counterclockwise
(three turns of screw = ½ roller revolution) to increase drop.
3 Test by running screen up about 1' and back down to new down limit.
4 Repeat steps 2 and 3 until desired position is reached.
"UP" LIMIT ADJUSTMENT
“Up” limit switch, located immediately above left end of automatic trap door, is
tripped as door closes. If door does not close fully, limit switch should be raised
slightly. If door closes too tightly, switch should be lowered slightly.
Remove steel plate attached to threaded neck of “up” limit switch by removing hex
nut securing it. Removing plate exposes three Phillips head machine screws which
hold limit switch bracket in place. Turning these screws clockwise will raise limit
switch; turning them counterclockwise will lower it.
Raise switch only in quarter-turn increments. When operating properly automatic
trap door should close gently and rest against but not press on rubber bumpers
above it. Adjusting automatic door so that it closes too tightly will damage screen.
1
1
/4"
1
1
/4"
2
1
/4"
5
/8"
2"
2"
Ceiling grid and tile
(by others)
7
9
/16"
®
automatically when fully down or fully up.
24V Control — Three-button up-stop-down switches stop at any point desired,
operate in any sequence. Factory adjusted limit switches automatically stop screen
when fully down or fully up.
Key Operated Switching — Two kinds of key-operated switches are optionally
available with this unit. 1 The key-operated power supply switch controls power to
the screen and switches. When it is “off”, the switches will not operate screen. Key
may be removed from the switch in either “on” or “off” position. 2 A three-position
key switch permits the screen to be operated directly by key. In this case, the
screen’s operator must always have a key.
RS232/Ethernet—Serial communication and network communication optionally
available with wall switches, RF or IR remote.
If you encounter any difficulties installing or servicing your Envoy screen, call your dealer or
Draper, Inc., Spiceland, Indiana, (765) 987-7999 or fax (765) 987-7142.
Caution: Do not remove the roller assembly from the case unless
necessary for repairs. If the roller assembly is removed, be sure motor
is fully re-seated in the bracket, and re-secure it carefully with the motor
retaining spring (see diagram below).
These instructions are meant as a guide only. They do not imply any responsibility
on the part of the manufacturer for improper installation or faulty workmanship at
the jobsite.

Consulta qui gratuitamente il manuale per il Draper Envoy. Il manuale rientra nella categoria Schermi per proiettori ed è stato valutato da 1 persone con una media di 7.4. Il manuale è disponibile nelle seguenti lingue: Inglese. Hai domande sul Draper Envoy o hai bisogno di aiuto? Fai la tua domanda qui

Ho bisogno di aiuto?

Hai una domanda relativa a Draper e la risposta non è nel manuale? Fai qui la tua domanda Fornisci una descrizione chiara e completa del problema e della tua domanda. Migliore sarà la descrizione del tuo problema e della domanda, più facile sarà per gli altri proprietari di Draper fornirti una buona risposta.

Numero di domande: 0

Generale
Draper
Envoy | 112037
Schermo per proiettore
641092114208, 0641092114482, 6410921144822
Inglese
Manuale d'uso (PDF)
Prestazione
Rapporto d'aspetto nativo5:4
Ampiezza dello schermo visibile (L)305 mm
Altezza dello schermo visibile (A)244 mm
Dimensione totale dello scermo (Altezza x Ampiezza)244 x 305 cm
Diagonale- "
Gain dello schermo2.5
Dimensioni e peso
Case L13430 mm
Peso64000 g
Altezza244 mm
Larghezza305 mm
Mostra di più

Non riesci a trovare la risposta alla tua domanda nel manuale? Puoi trovare la risposta alla tua domanda nelle FAQ sul Draper Envoy che trovi di seguito.

La tua domanda non è elencata? Fai la tua domanda qui

Nessun risultato