Electrolux EWE361KA-DWG6 manuale

Electrolux EWE361KA-DWG6
7.5 · 1
PDF manuale
 · 2 pagine
Inglese
manualeElectrolux EWE361KA-DWG6
EN ELECTRIC WATER HEATER USER MANUAL

1. PARTS IDENTIFICATION

1. Front Cover2. LED Indicators i) Earth LED Indicator ii) Power/ELCB LED Indicator3. Test / Reset Button4. Face Panel5. Pump Button*6. Temperature Control Knob7. 3 in 1 Stop Valve i) Stop Valve Lever ii) Flow Regulator Valve Adjustment iii) Built-in-Filter8. Mesh Filter 9. Rail Support 10.
Handshower11. Adjustable Shower Holder12. Slider Rail13. PVC Hose14. Soap Tray15. Heater Base16. Terminal Block17. Thermostat (Double-Action)18. Heater Tank19. PCB Board (Test & Reset)20. VR Board21. Main/ELCB Board**22. Water Outlet Connection23. AC Pump* 24. TRIAC25. Reed Switch Assy***26. Water Inlet Connection***27. SMPS PCB Board28. D.C. Silent Pump*29. Rating Label 30. Pump Board31 Shower Bracket Holder
2.
SAFETY INFORMATION
2.1 Products manufactured by Electrolux are safe provided they are installed, used and maintained in good working order in accordance with our instructions and recommendations. Always refer to this manual if you have any doubt. 2.2 The Electric Water Heater must be earthed. Improper grounding could cause electrical shock.2.3 If any of the following conditions occur as shown below, immediately switch off the power supply and contact the Electrolux Consumer
2.6 When the Electric Water Heater is used by someone such as child, elderly person, sick person and physically handicapped person, the person concerned is kindly requested to pay attention and check the shower temperature by hand from time to time.2.7 During lightning/thunder, switch off the power supply to the Electric Water Heater in advance to protect the Electric Water Heater against possible damage.2.8 The earth continuity conductor of the electrical installation must be effectively connected to all exposed metal parts of other appliances and services in the room, which in the Electric Water Heater is to be installed to conform to local regulations and ensure proper earthing/grounding for ELCB to be effective. NOTE : When removing
th
e Electric Water Heater from package, a small amount of water may be found inside. This is normal as the Electric Water Heater is tested during manufacturing process.
WARNING !
.
.
.
.
.
If the Electric Water Heater begins to make an odd noise, smell or smoke.If ELCB trips and Electric Water Heater Indicator does not light up. Water temperature cannot be controlled.If the Electric Water Heater shows signs of a distinct change in performance.If water leaks from inside.2.10 Installation must be carried out by a qualied personnel and in compliance local 2.11 This Electric Water Heater must be permanently connected to the direct main lin
e
su
pply. A plug and socket is not recommended to be used.2.12 For the correct size of wire conductor corresponding to different electrical loadings,
2.13 This Electric Water Heater operates at a
minimum water ow rate of 2.0 litre/min and maximum working
2.14 The Electric Water Heater will not function
if there is insufcient water ow (min 2.0 litre/min
2.15
The built-in ELCB will automatically cut off
the
power supply in case there is a current
2.16
The thermostat will automatically cut off the
power supply if it has sensed an abnormal rise in water temperature.CAUTION !authority regulations. please refer to Table 1.pressure of 6 bars. For direct connection from the water tank, theElectric Water Heater must have an installation minimum 1.0m below the water tank.leakage over 15mA.Care Center. Never attempt to repair the Electric Water Heater yourself: 2.5 For Pump Model, it is highly recommended to connect the Water Inlet Connection to tank storage supply, otherwise it may cause damage to the Pump Motor.User is advised to test and adjust the water temperature before using.2.9 WARNING : Metallic / chromed hose and conductive control valve shall not be used.
3. ELECTRIC WATER HEATER UNIT INSTALLATION
3.1 Select a suitable position in the bathroom.3.2 Remove the screw (A) at the bottom of the Electric Water Heater. (Fig. 2)3.3 Remove the Front Cover from the bottom and then lift up the front cover.3.4 Mark 3 Screw points of the Heater Base on the wall. The Electric Water Heater position should be 1.5m above the bathroom floor. (Fig. 2)3.6 Use 6mm diameter drill and make the wall plug holes in depth of 34mm ,for mount the Electric Water Heater.3.7 Insert the wall plugs and mount the Electric Water Heater firmly in position with the screws provided.3.8 Insert the Shower Holder and Soap Tray into the Slider Rail. 3.9 Insert the Rail Bracket to both end of the Slider Rail Bar.3.10 Remove the cap from the Rail Bracket and screw the Bracket to marked position. Replace the cap. (Fig. 3)
connect to
water outlet
connection
ELECTRIC WATER HEATER
UNIT INSTALLATION DIAGRAM
Fig. 2
Screw
A
3 in 1
stop valve
inlet
Wall
285.5mm
Washer
connect to
water inlet
connection
Min.
80 mm
150mm
OFF
4. PLUMBING PROCEDURE
CAUTION!IMPORTANTThis Electric Water Heater is a single point system and the “Water Outlet” can only be fitted to the Hose and Handshower set provided. MUST NOT TO CONNECT CONTROL VALVE OR FITTING CAN BE FITTED TO THE WATER OUTLET.WARNING!
5.
ELECTRICAL INSTALLATION
WARNING!PROCEDURE :5.7 Connect the cable as following: (Fig. 5)BROWN or RED --LIVE (L)BLUE or BLACK --NEUTRAL (N)GREEN or GREEN/YELLOW --EARTH ( )5.8 Clamp the cable to the correct position.Technician need to confirm the wire before installation. CHECK IF THE WIRING CONNECTION IS CORRECT and replace the cover.5.9 When putting back the Front Cover, please take note of the procedure shown below :-Ensure the position is correct, turn the Temperature Control Knob Insert to OFF position as shown in Fig.A (At the Heater Base)-Install the Front Cover,turn the Temperature Control Knob to OFF position to align with the VR shaft as shown in Fig.B (At the Front Cover)5.10 Fix the Temperature Control Knob and screw ‘A’ (Fig. 2).5.1 This Electric Water Heater must be earthed. Improper grounding could cause electrical shock.5.2 Remember to SWITCH OFF the power supply before carrying out any electrical work.5.3 Refer to TABLE 1 for the correct cable size.5.4 Use double insulation cable of over 2.5mm²for 2.4kW, 3.5kW 3.8kW, 4.5kW 4.8kW models and 4mm² for 3.6kW and 6.0kW model. 5.5 Lead the power cable from MCB to a “ON/OFF’’ double pole Linked Switch having a contact separation of at least 3mm in all poles outside the bathroom, then lead a cable to the terminal block inside the Electric Water Heater. (Fig. 4)5.6 Insert the wall embedded cable through Side Entry ‘A’ by cutting a hole at the source cord rubber holder and lead the cable to Cable Bracket ‘B’. (Fig. 6)Always KEEP the water supply to the Electric Water Heater free from mud and dirt at all time during usage.4.1 Connect the 3 in 1 Stop Valve to the Water Inlet with washer. Use correct tools to tighten and be careful not to over tighten and damage the plastic nut.4.2 Connect the incoming water piping to the 3 in 1 Stop Valve (1/2” BSP).Make sure to put the Mesh Filter between 3 in 1 Stop Valve and incoming water piping.4.3 If in any case, the 3 in 1 Stop Valve is not use or omitted, make sure to put the Mesh Filter between the Electric Water Heater inlet pipe and incoming water pipe.4.4 Turn on the water mains to drain out all plumbing dirts before connecting the water supply to the Electric Water Heater, the water supply to the Electric Water Heater must be free from mud and dirt. 4.6 Hook the Handshower to the Slider Rail Shower Holder and adjust to your ideal position.4.7 Check if any water leakage.4.8 Do not use sealing tape during piping installation.THE HEATER TANK MUST BE FILLED UP WITH WATER BEFORE TURNING ON THE POWER SUPPLY TO PREVENT ANY DRY BURNT DAMAGE TO THE HEATING ELEMENT.4.5 Connect the Hose and Handshower to the outlet of Electric Water Heater, be sure to put in the Washer in between the connection. (Fig. 2)4.10 DO NOT APPLY PLUMBING CEMENT ON CONNECTION. WHENEVER NECESSARY, USE ONLY THREAD OR SEALING TAPE.4.9 THE WATER INLET AND OUTLET MUST BE INSTALLED CORRECTLY, OTHERWISE ELECTRIC WATER HEATER WILL NOT FUNCTION.5. ELECTRICAL INSTALLATION (CONT’D)

6. TABLE 1 - CABLE SIZE TABLE

Power Current (kW) (A) 220V ~50/60 Hz Conductor Size (csa)mm Conduit Cable Flexible Cable On/ Off Fuse / Switch (A) MCB (A) 2.4 10.9 2.5 7 / 0.67mm 50 / 0.25 mm 20 20 3.5 15.9 2.5 7 / 0.67mm 50 / 0.25 mm 20 20 4.5 20.5 2.5 7 / 0.67mm 50 / 0.25 mm 32 32 6.0 27.3 4.0 7 / 0.85mm 56 / 0.30 mm 32 32
2
Voltage
(AC)
3.6 15.0 4.0 7 / 0.85mm 56 / 0.30 mm 20 20240V ~50/60 Hz
(Malaysia Model)
METHOD OF ALIGNMENT WHEN REPLACING FRONT COVER
Cable
Fig. 4
Brown or Red = Live (L)Blue or Black = Neutral (N)Green or Green/ Yellow = Earth ( )Fig. 5
Fuse Distributor Board
Miniature Circuit Breaker (MCB)
ON/OFF Double Pole Switch
Double PVC cable
NOTE:
Refer to TABLE 1 for electrical loading and
correct size of wire conductor
A
B
Fig. 6
Front Cover
Fig A
Fig B

OFF

Position

this Way

OFF

Position

this Way

1 2
3
4
5
(2.2 ℓ/Min for 4.8kW & 2.5 ℓ/min for 6.0kW model only)/ 2.2 ℓ/Min for 4.8kW & 2.5 ℓ/min for 6.0kW model only) to trigger the flow switch.
REV 1

Fig. 3a

(Thailand, Indonesia, Philippines,

and Malaysia pump model)

SHOWER SET INSTALLATION DIAGRAM

Fig. 3b

(Malaysia standard model)

SHOWER SET INSTALLATION DIAGRAM

Cap

Screw

Rail Bracket

Adjustable

Shower

Holder

Wall Plug

Slider

Rail Bar

Flexible Angle

Adjustment

Flexible

Hose

Hand

Shower

PVC Hose

Shower

Screw

Shower

Holder

Cover

Shower

Holder

Cover

Head

SLIDER BAR ACCESSORIES

(Single Spray)

BRACKET ACCESSORIES

(Single Spray)

3.5. Slider Bar Accessories: Mark 2 screw points of the Slider Rail beside the Electric Water Heater.
It is recommended that the top of the portion is in level with the top of Electric Water Heater. (Fig. 3 & 3a)
Bracket Accessories: Open the Shower Holder cover, mark 2 screw point of the Shower Holder beside
the Electric Water Heater. It is recommended that the top of the portion is in level the top ElectricWater Heater. After screw the Shower Holder, put back the shower holder cover. (Fig. 3b)

EWE361KA-DWG6

EWE381KX-DWG6

EWE481KX-DWG6

EWE601KX1DWG6

EWE351KX-DWX6

EWE361KA-DWP6

EWE451KX-DWB2

EWE241KX-DWB6

EWE351KX-DWB6

EWE451KX-DWB6

EWE361KA-DWB6

EWE361KX-DWB5

EWE361KX-DWX5

3.8 17.3 2.5 7 / 0.67mm 50 / 0.25 mm 20 20 4.8 21.8 2.5 7 / 0.67mm 50 / 0.25 mm 32 322.4 If the Red (POWER) Indicator does not go offwhen you turn off the water, switch OFF the
mains supply and contact Electrolux ConsumerCare Centre for repair service.Special skill isrequired for repairing. NEVER try to repair the unit by yourself.
15
16
18
19
22
21
23
24
25
26

OFF

7
8
27
24
25
26

OFF

7
8
28

No Pump model

24
25
26

OFF

7
8

AC Pump model

DC Pump model

Fig. 1

15
16
18
19
22
20
21
17
17
15
16
18
19
17
9
10
12
13
14
11

OFF

7
8
1
5
4
29
30
22
21
30
6
*
*
*
3
2
* For Pump Model only** Pump Model VR Board & Main/ELCB Board combine.
10
31
13
9
10
12
13
11
Slider Bar Accessories(Single Spray)Bracket Accessories(Single Spray)Slider Bar Accessories* ** * **

** **

Fig. 3 (Vietnam only)

SHOWER SET INSTALLATION DIAGRAMFlexible AngleAdjustment5 Spray Patterns SelectionHand ShowerFlexible
Hose
Soap
Tray
Slider Rail BarAdjustable Shower HolderScrewWall
Plug
MountingTerminalconnect to water outletconnection Rail bracket
cap
Hexagon tool(Tighten plastic nut before close cap)Plastic nutFig 3C

RAIL BRACKET COVER & CAP DISMANTLE STEPS FOR SLIDER BAR ACCESSORIES

1
RAIL BRACKET
2
OPEN THE RAIL BRACKET COVERBY TURNING ANTI CLOCKWISE & USING SCREW DRIVER TO OPEN THE CAP
3
RAIL BRACKET COVER COME-OUT
Fig 1.
Slide Bar Accessories (Vietnam only)
Slide Bar Accessories (Single Spray – Thailand, Indonesia, Philippines, and Malaysia pump model)
Bracket Accessories (Single Spray – Malaysia standard model)
***
***
*** No pump Model 4.8kW & 6.0kW using Flow Sensor Assembly.

Consulta qui gratuitamente il manuale per il Electrolux EWE361KA-DWG6. Il manuale rientra nella categoria Scaldabagno ed è stato valutato da 1 persone con una media di 7.5. Il manuale è disponibile nelle seguenti lingue: Inglese. Hai domande sul Electrolux EWE361KA-DWG6 o hai bisogno di aiuto? Fai la tua domanda qui

Ho bisogno di aiuto?

Hai una domanda relativa a Electrolux e la risposta non è nel manuale? Fai qui la tua domanda Fornisci una descrizione chiara e completa del problema e della tua domanda. Migliore sarà la descrizione del tuo problema e della domanda, più facile sarà per gli altri proprietari di Electrolux fornirti una buona risposta.

Numero di domande: 0

Generale
Electrolux
EWE361KA-DWG6
Scaldabagno
Inglese
Manuale d'uso (PDF)

Non riesci a trovare la risposta alla tua domanda nel manuale? Puoi trovare la risposta alla tua domanda nelle FAQ sul Electrolux EWE361KA-DWG6 che trovi di seguito.

La tua domanda non è elencata? Fai la tua domanda qui

Nessun risultato