Lancom LN-1700B

Lancom LN-1700B manuale

(1)
  • a Power
    Off Device switched off
    Green, permanently* Device operational,
    resp. device paired / claimed and LANCOM
    Management Cloud (LMC) accessible.
    Orange, permanently No adequate PoE-power supply via
    802.3af, operation of the second Wi-Fi
    interface not possible
    Red / green, blinking Conguration password not set. Without a
    conguration password, the conguration
    data in the device is unprotected.
    Orange / green,
    blinking alternately
    with the WLAN link
    LED
    At least one Wi-Fi module is in
    managed mode and has not found a
    WLAN controller yet. The corresponding
    Wi-Fi module(s) is/are switched off until a
    WLAN controller has been found to supply
    a conguration, or until being switched
    manually into another operating mode.
    Orange / red,
    blinking alternately
    with the WLAN link
    LED
    At least one Wi-Fi module is in managed
    mode and has found a WLAN controller.
    However, the WLAN controller cannot
    assign a conguration because the
    rmware and/or the device's loader
    version is not compatible with the WLAN
    controller.
    1x green inverse
    blinking*
    Connection to the LMC active, pairing OK,
    claiming error.
    2x green inverse
    blinking*
    Pairing error, resp.
    LMC activation code / PSK not available.
    3x green inverse
    blinking*
    LMC not accessible, resp.
    communication error.
    b WLAN link
    Off No Wi-Fi network dened or Wi-Fi module
    deactivated. The Wi-Fi module is not
    transmitting beacons.
    Green, permanently At least one Wi-Fi network dened and
    Wi-Fi module activated. The Wi-Fi module
    is transmitting beacons.
    Green, inverse ashing Number of ashes = number of connected
    Wi-Fi stations and P2P wireless
    connections, followed by a pause (default).
    Alternatively the ashing frequency can
    indicate signal strength over the dened
    P2P link or the signal strength between the
    access point and the device operating in
    client mode.
    Green, blinking DFS scanning or other scan procedure
    Red, blinking Wi-Fi module hardware error
    MOUNTING AND CONNECTING THE DEVICE
    Hardware
    Power supply 12 V DC, external power adapter (110 V or 230 V) with bayonet connector to secure against
    disconnection or PoE based on 802.3at via ETH1
    Power consumption Approx. 21 W via 12 V / 2 A power adapter (value refers to the total power consumption of
    access point and power adapter),
    Approx. 19.4 W via PoE (value solely refers to the power consumption of the access point)
    Environment Temperature range 0–45 °C (vertical wall mount with LANCOM Wall Mount (LN)),
    0-37 °C (horizontal ceiling mount with LANCOM Wall Mount (LN))
    Access point overheating is avoided by automatic throttling of the Wi-Fi modules
    Humidity 0-95 %; non-condensing
    Housing Robust synthetic housing, rear connectors, ready for wall and ceiling mounting; measures
    205 x 42 x 205 mm (W x H x D)
    Number of fans None; fanless design, no rotating parts, high MTBF
    Wi-Fi
    Frequency band 2400-2483.5 MHz (ISM) or 5180-5700 MHz (restrictions vary between countries)
    Radio channels 2.4 GHz Up to 13 channels, max. 3 non-overlapping (2.4 GHz band)
    Radio channels 5 GHz Up to 19 non-overlapping channels (automatic dynamic channel selection required)
    Bluetooth Low Energy
    iBeacon The device can broadcast a congurable iBeacon.
    Scanner The device can collect data of BLE devices in the neighborhood and forward this data to
    external systems for evaluation purposes.
    Interfaces
    ETH1 (PoE) 10 / 100 / 1000 Base-TX, autosensing, auto node hub, line bundling via LACP,
    PoE adapter compliant to IEEE 802.3at required
    ETH2 10 / 100 / 1000 Base-TX, autosensing, auto node hub, line bundling via LACP
    Serial interface Serial conguration interface / COM-port (8-pin mini-DIN): 9,600 - 115,000 baud
    Declaration of conformity
    Hereby, LANCOM Systems GmbH | Adenauerstrasse 20/B2 | D-52146 Wuerselen, declares that this radio equipment is
    in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following
    internet address: www.lancom-systems.com/ce/
    Package content
    Documentation Installation Guide (DE / EN), Quick Reference Guide (DE / EN)
    Antennas
    (only LN-1702B)
    Six 3dBi dipole dual-band antennas
    Cable Ethernet cable, 3 m
    Power adapter External power adapter, NEST 12 V / 2 A DC/S, barrel connector 2.1 / 5.5 mm bayonet,
    LANCOM item no. 111590 (EU, 230 V) (not for WW devices)
    LANCOM, LANCOM Systems and LCOS are registered trademarks. All other names or descriptions used may be trademarks or registered
    trademarks of their owners. Subject to change without notice. No liability for technical errors and/or omissions. 111811/0120
    TECHNICAL DETAILS
    ETH2ETH1 (PoE) Reset Config (Com)DC 12 V
    *) The additional power LED statuses are displayed in 5-seconds
    rotation if the device is congured to be managed by the LANCOM
    Management Cloud.
    LANCOM LN-1700B
    LANCOM LN-1702B
    Quick Reference Guide
    4
    Please observe the following when setting up the device
    A For devices to be operated on the desktop, please attach the adhesive rubber
    footpads
    A Do not rest any objects on top of the device
    A Keep the ventilation slots on the side of the device clear of obstruction
    a
    Wi-Fi antennas (only LN-1702B)
    Screw the two supplied Wi-Fi antennas onto the connectors WLAN 1 Ant 1 / Ant 2
    and WLAN 2 Ant 1 to Ant 4. The desired MIMO behaviour can be congured under
    > Physical WLAN Settings
    > Radio
    > Antenna grouping
    b
    Power
    After connecting the cable to the device, turn the connector 90° clockwise to
    prevent it from accidental un plugging. Use only the supplied power adapter.
    c
    Ethernet interface
    Use the cable with the Ethernet connectors to connect interface ETH1 (PoE)
    or ETH2 to your PC or a LAN switch.
    d
    Reset button
    Pressed up to 5 seconds: device restart
    Pressed until rst ashing up of all LEDs:
    conguration reset and device restart
    e
    Serial interface
    You can optionally congure the device by connecting it to a PC with a
    conguration cable (separately available).
    c
    b d
    WLAN 2 Ant 3
    WLAN 2 Ant 4
    WLAN 2 Ant 2
    WLAN 2 Ant 1
    WLAN 1 Ant 1WLAN 1 Ant 2
    a
    a
    a b
    Cloud-ready
    e
    A Lockable wall and ceiling mounting with the LANCOM Wall Mount (LN)
    (available as an accessory)
    A Please note that when operating both Wi-Fi modules in the same frequency band,
    mutual interference cannot be ruled out
    Before initial startup, please make sure to take notice of the information regarding the intended use in the enclosed installation guide!
    Operate the device only with a professionally installed power supply at a nearby power socket that is freely accessible at all times.
Lancom LN-1700B

Ho bisogno di aiuto?

Numero di domande: 0

Hai domande sul Lancom LN-1700B o hai bisogno di aiuto? Fai qui la tua domanda. Fornisci una descrizione chiara e completa del problema e della domanda. Più dettagli fornisci per il tuo problema e la tua domanda, più facile sarà per gli altri proprietari di Lancom LN-1700B rispondere correttamente alla tua domanda.

Consulta qui gratuitamente il manuale per il Lancom LN-1700B. Il manuale rientra nella categoria Punto di accesso ed è stato valutato da 1 persone con una media di 9. Il manuale è disponibile nelle seguenti lingue: Inglese. Hai domande sul Lancom LN-1700B o hai bisogno di aiuto? Fai la tua domanda qui

Specifiche Lancom LN-1700B

Generale
Marca Lancom
Modello LN-1700B
Prodotto Punti di accesso
EAN 4044144617935
Lingua Inglese
Tipo di file PDF
Design
Colore del prodotto Bianco
Installazione Table,Wall
Materiale della scocca Sintetico
Indicatori LED
Blocco cavo
Tipologia slot blocco cavo Kensington
Certificazione EN 60950-1, EN 301 489-1, EN 301 489-17\nEN 301 893\nEN 300 328
Paese di origine Germania
Tasto reset
Caratteristiche
2.4 GHz
5 GHz
Velocità massima di trasferimento dati 1733 Mbit/s
MIMO
Tipo MIMO Multi User MIMO
Gamma di frequenza 160 MHz
Banda di frequenza 2.4 - 2.4835, 5.15 - 5.35, 5.47 - 5.725 GHz
Standard di rete IEEE 802.11a,IEEE 802.11ac,IEEE 802.11b,IEEE 802.11d,IEEE 802.11e,IEEE 802.11g,IEEE 802.11h,IEEE 802.11i,IEEE 802.11k,IEEE 802.11n,IEEE 802.11r,IEEE 802.11u,IEEE 802.11v,IEEE 802.11w,IEEE 802.1D,IEEE 802.1x,IEEE 802.3,IEEE 802.3ab,IEEE 802.3at,IEEE 802.3az,IEEE 802.3u
Modulazione 256-QAM
Roaming veloce
VLAN support
Numero di ID VLAN 4096
Caratteristiche della LAN virtuale Stacked VLAN,Tagged VLAN
Limitazione della velocità
Supporto qualità del servizio (QoS)
Velocità trasferimento Ethernet LAN 10,100,1000 Mbit/s
Selezione della frequenza dinamica (DFS)
Selezione automatica dei canali
Raggio d'azione interno 30 m
Raggio d'azione esterno 150 m
Wi-Fi Multimedia (WMM)/(WME)
Funzione del canale WLAN Gestione dei canali WLAN
Velocità massima di trasferimento dati (2,4 GHz) 450 Mbit/s
Airtime Fairness (ATF)
Direzione della banda
Combinazione di rapporto massima
Sensibilità ricevitore WLAN-1, 5 GHz:\nIEEE 802.11a/h: -98 dBm @ 6 Mbps, -81 dBm @ 54 Mbps, IEEE 802.11n: -94 dBm @ (MCS0, 20 MHz), -76dBm @ (MCS 7, 20 MHz),\n-92 dBm @ (MCS0, 40 MHz), -72 dBm @ (MCS7, 40 MHz)\n\nWLAN-1, 2.4 GHz:\nIEEE 802.11b: -97 dBm @ 1 MBit/s, -93 dBm @ 11 MBit/s, IEEE 802.11g: -95dBm @ 6 MBit/s, -81dBm @ 54 MBit/s IEEE 802.11n: -94\ndBm @ 6,5MBit/s (MCS0, 20 MHz), -77 dBm @ 65 MBit/s (MCS7, 20 MHz), -91 dBm @ 15 MBit/s (MCS0, 40 MHz), -74 dBm @ 150\nMBit/s (MCS7, 40 MHz)
Funzioni Wi-Fi Multimedia (WMM) Risparmio energetico WMM
Adatto alle funzioni della modalità AP Hotspot 2.0,Wireless distribution system (WDS)
Roaming Wi-Fi
Sicurezza
Algoritmi di sicurezza supportati EAP-GTC,AES-CCMP,AES-GCMP,802.1x RADIUS,EAP-FAST,EAP-LEAP,EAP-MD5,EAP-TLS,EAP-TTLS,MSCHAPv2,PEAP,SSH,SSL/TLS,TKIP,WEP,WPA2,WPA3
Numero di supporti SSID 31
Funzione IGMP snooping
Lista di controllo accesso (ACL)
Servizio utente di autenticazione remota in entrata (RADIUS)
Wireless Distribution System (WDS) automatico
Snooping DHCP
Identificazione delle sorgenti di interferenza
Funzioni SSID (Service Set Identifier) Multiple SSIDs
Sistema di rilevamento delle intrusioni wireless (WIDS)
Antenna
Tipo di antenna Interno
Livello di guadagno dell'antenna (max) 4.5 dBi
Caratteristiche dell'antenna Antenna integrata
Protocolli
Protocollo di routing RIP-2,VRRP
Server DHCP
Cliente DHCP
Protocolli di rete supportati IPv4: DNS, HTTP, HTTPS, ICMP, NTP/SNTP, NetBIOS, PPPoE (server), RADIUS, RADSEC (secure RADIUS), RTP, SNMPv1,v2c,v3, TFTP, TACACS+, IPv6: NDP, SLAAC, ICMPv6, DHCPv6, DNS, HTTP, HTTPS, PPPoE, RADIUS, SMTP, NTP, SNMPv1,v2c,v3
Protocolli di gestione SNMPv1,v2c,v3
Caratteristiche IPv4 e IPv6 Dual stack IPv4/IPv6
Connettività
Quantità porte Ethernet LAN (RJ-45) 2
Connessione RS232
Quantità porte USB 2.0 0
Jack DC-in
Porta WAN Ethernet (RJ-45)
Gestione energetica
Supporto Power over Ethernet (PoE)
Voltaggio di ingresso 230 V
Voltaggio di uscita 12 V
Consumo energetico (max) 21 W
Dati su imballaggio
Adattatore AC/DC No
Cavi inclusi LAN (RJ-45)
Numero di prodotti inclusi 1 pezzo(i)
Condizioni ambientali
Intervallo temperatura di funzionamento 0 - 45 °C
Range di umidità di funzionamento 0 - 95 %
Dimensioni e peso
Larghezza 205 mm
Profondità 205 mm
Altezza 42 mm
Caratteristiche di gestione
Gestione web-based
Syslog
Firmware aggiornabile