Smartwares VD38W

Smartwares VD38W manuale

(2)
  • 14 15 16 12
    13
    17 18
    9 10
    17
    1
    3
    12
    5
    4
    7
    8
    6
    9
    10
    11
    2
    11
    OPTIONAL:
    TOWARDS THE
    DOOR LOCK
    1
    3 4 5
    6
    2
    T
    12V 1Amp MAX
    Always test the product on site before installation.
    Be aware that different materials in between the Outdoor Intercom
    and Indoor Monitor will affect the operating performance of the product.
    Follow the Wiring and pairing guides to test the product.
    Install the Outdoor Intercom in a dry location if possible.
    Mount the Intercom at a suitable height and position to allow the
    camera to see the visitor
    Battery setup:
    Outdoors intercom
    1. On the back of the intercom, remove the 6 screws on the battery
    compartment, and remove the cover
    2. Insert the battery pack into the compartment, making sure it is positioned
    correctly, with the marking "Rechargeable Li-Ion battery" facing you.
    3. Replace the battery compartment cover and insert the 6 screws.
    Indoor Monitor
    1. On the back of the indoor monitor, open the battery compartment
    cover pulling towards you.
    2. Insert the battery pack into the compartment, making sure it is positioned
    correctly, with the marking "Rechargeable Li-Ion battery" facing you.
    3. Replace the compartment cover.
    Installation and setup Outdoor intercom wall support
    Key features
    CAUTION
    1. Please read these instructions before setting up and using the device.
    2. Do not cut the power supply cable to extend it; the transformer will not operate with
    a longer cable. Do not plug in the transformer until all the wiring has been finished.
    3. This product is not a toy. Keep it out of reach of children.
    4. Do not operate electrically powered products in explosive atmospheres, such as
    in the presence of flammable liquids, gases, or dust. Electrically powered products
    may create sparks which are likely to ignite dust or create fumes.
    5. The warnings, precautions, and instructions presented in this instruction manual
    cannot cover all possible conditions and situations that may occur the operator must
    understand that common sense and caution are factors that the product can not
    provide but the operator must put in place.
    6. Do not expose the power adapter for this product to rain or moisture.
    Water entering the Power Adapter will increase the risk of electric shock.
    7. Do not abuse the Power Cord. Never use the cord for unplugging the plug from the outlet.
    Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords
    increase the risk of electric shock.
    8. The adapter must match the power outlet.
    Never modify the cord in any way. Unmodified plugs and suitable outlets will reduce
    risk of electric shock.
    1. Antenne
    2. Screen
    3. UP button
    4. LEFT button
    5. RIGHT button
    6. OK / Photo button
    7. DOWN button
    8. Intercom button
    9. Door lock button
    10. Monitor button
    11. Microphone
    12. LED lighting
    13. USB port
    14. Power ON/OFF
    15. Metal support screws
    16. Metal supports
    17. Wall mount
    18. Battery compartment cover
    1. Rain cover
    2. Microphone
    3. Camera lens
    4. Night vision lighting
    5. Speaker
    6. Name plate
    7. Call button
    8. Light sensor
    9. Antenne
    10. Battery compartment
    11. Screw
    12. Power and locking connector
    Included in the pack:
    Inside
    Indoor Monitor Outdoors intercom
    Outside
    OPTIONAL
    x2
    1. Select the location of the outdoor intercom, use the rain cover as a
    template anD drill the holes to mount the plugs.
    2. Mark and drill the hole in order to feed the electric cables through the wall.
    3. Push the electric cables so that they are visible from the outside.
    4. Glue the seal inside the rain cover.
    5. Mount the rain cover with the mounting hardware included.
    Pay attention to the mounting bracket on the lower support,
    making sure the electric cables will fit through the joining
    opening of the back plate in the lower corner.
    6. Link the intercom electric cables as shown on the wiring diagram below.
    7. Firstly, insert the upper part of the intercom into the rain cover and
    place the lower part on the angled support.
    8. Secure the intercom in place on the rain cover using the securing screws.
    Name plate
    1. If you need to fill the name plate, push strongly on the left side whilst
    sliding the plate to the left in order to free the right side and then remove it.
    2. Use a pointy object to remove the name plate from the inside of the
    plate and fill-in your details.
    3. Then, replace the label and follow the same steps in the opposite
    order to reassemble the plate in the outdoor unit.
    1. With a small screw driver, push the connexion bloc upwards on
    the outdoor intercom in order to detach it.
    2. Connect the DC power supply to the terminals marked + and -,
    checking that the wires are linked correctly.
    3. If required, connect the door lock cables to the 2 terminals, checking
    the correct power supply to the door lock (only for an electric door lock,
    max. 12 V, 1 A , through a separate power plug - NOT INCLUDED).
    4. Replace the connector in the outdoor intercom, making sure the
    polarity is correct.
    Name plate Wiring
    13-20mm
Smartwares VD38W

Ho bisogno di aiuto?

Numero di domande: 0

Hai domande sul Smartwares VD38W o hai bisogno di aiuto? Fai qui la tua domanda. Fornisci una descrizione chiara e completa del problema e della domanda. Più dettagli fornisci per il tuo problema e la tua domanda, più facile sarà per gli altri proprietari di Smartwares VD38W rispondere correttamente alla tua domanda.

Consulta qui gratuitamente il manuale per il Smartwares VD38W. Il manuale rientra nella categoria Telecamera di sorveglianza ed è stato valutato da 2 persone con una media di 8.6. Il manuale è disponibile nelle seguenti lingue: Inglese. Hai domande sul Smartwares VD38W o hai bisogno di aiuto? Fai la tua domanda qui

Specifiche Smartwares VD38W

Non è necessario acquistare altoparlanti esterni per un avere un audio eccezionale. Con gli altoparlanti integrati, ques...
Generale
Marca Smartwares
Modello VD38W
Prodotto Telecamere di sorveglianza
Lingua Inglese
Tipo di file PDF
Dettagli tecnici
A colori
Telefono con vivavoce
Numero di display supportati 1
numero massimo di fotocamere supportate -
Altoparlanti incorporati
Microfono incorporato
Raggio d'azione esterno 175 m
Display
Dimensioni schermo 3.5 "
Tecnologia display TFT
Design
Colore del prodotto Bianco
Tipo di controllo Pulsanti
Macchina fotografica
Angolo di campo visivo 45 °
Gestione energetica
Adattatore di corrente output AC 1 A
Adattatore di voltaggio output AC 5 V

Domande frequenti

Di seguito, troverai le domande più frequenti riguardo Smartwares VD38W .

La tua domanda non è elencata? Fai la tua domanda qui