Sony MDR-1RNC manuale

  • MDR-1RNC [US, FR, ES] 4-448-091-41(1)
    © 2012 Sony Corporation Printed in Malaysia
    English Noise Canceling Headphones
    Do not expose the battery to excessive heat such as direct
    sunlight, fire or the like.
    For customers in the USA
    The following FCC statement applies only to
    the version of this model manufactured for
    sale in the USA. Other versions may not comply
    with FCC technical regulations.
    This equipment has been tested and found to comply
    with the limits for a Class B digital device, pursuant to Part
    15 of the FCC Rules. These limits are designed to provide
    reasonable protection against harmful interference in a
    residential installation. This equipment generates, uses
    and can radiate radio frequency energy and, if not installed
    and used in accordance with the instructions, may cause
    harmful interference to radio communications. However,
    there is no guarantee that interference will not occur in a
    particular installation. If this equipment does cause harmful
    interference to radio or television reception, which can be
    determined by turning the equipment off and on, the user is
    encouraged to try to correct the interference by one or more
    of the following measures:
    Reorient or relocate the receiving antenna.
    Increase the separation between the equipment and
    Connect the equipment into an outlet on a circuit different
    from that to which the receiver is connected.
    Consult the dealer or an experienced radio/TV technician
    for help.
    You are cautioned that any changes or modifications not
    expressly approved in this manual could void your authority
    to operate this equipment.
    If you have any questions about this product, you may call:
    Sony Customer Information Service Center 1-800-222-7669
    Declaration of Conformity
    Trade Name: SONY
    Model No.: MDR-1RNC
    Responsible Party: Sony Electronics Inc.
    Address: 16530 Via Esprillo, San Diego,
    CA 92127 USA
    Telephone No.: 858-942-2230
    This device complies with Part 15 of the FCC Rules.
    Operation is subject to the following two conditions:
    (1) this device may not cause harmful interference, and
    (2) this device must accept any interference received,
    including interference that may cause undesired
    For customers in Canada
    The validity of the CE marking is restricted to only those
    countries where it is legally enforced, mainly in the countries
    EEA (European Economic Area).
    This Class B digital apparatus complies with Canadian
    Checking the remaining
    Status POWER Indicator Beep sound
    Blinks 3 times *
    No beep
    Blinks 2 times *
    No beep
    Blinks 1 time *
    No beep
    Empty Blinks quickly
    (30 seconds)
    Long beep
    (2 seconds)
    * When turning off the power of the headphones.
    How to use/Mode d’utilisation/Modo de uso
    Charging the headphones/Chargement du casque/Recarga de los auriculares
    Turning on the power/Mise sous tension/Encendido
    Wearing and controlling/Port et contrôles/
    Colocación y control
    After use
    Turn off the power of the headphones
    Après utilisation
    Éteignez le casque
    Después del uso
    Apague los auriculares
    Checking the charging
    Status Charging indicator
    Charging On
    Full Off
    Charging malfunction Blinks
    Using the Center button
    (Inline remote and
    microphone cord for
    Operation Explanation
    Single press Plays/pauses a track of the
    connected iPod.
    Double press Skips to the next track.
    Triple press Skips to the previous track.
    Long press
    Starts the “VoiceOver*” feature (if
    Press once when call is
    Answers the call.
    Press again Ends the call.
    Hold down for about
    two seconds and
    Rejects an incoming call (two
    low beeps confirm the call was
    * Availability of the “VoiceOver” feature depends on iPod
    and its software version.
    Be careful not to unintentionally press any buttons when
    you carry your iPod with this headphones connected.
    Automatic AI Noise
    The Automatic AI Noise Canceling function constantly
    analyzes environmental ambient sound components and
    automatically selects the most effective noise canceling
    Noise canceling mode types
    NC Mode A: Noise mainly in an airplane is effectively
    NC Mode B: Noise mainly in a bus or a train is effectively
    NC Mode C: Noise mainly found in an office environment
    (PC, copier, air ventilation, etc.) is effectively
    When the headphones are turned on, NC Mode A is set.
    It may take a few seconds to analyze the environmental
    ambient sound.
    Notes on use
    What is noise canceling?
    The noise canceling circuit actually senses outside noise
    with built-in microphones and sends an equal-but-opposite
    canceling signal to the headphones.
    Notes on the noise canceling function
    Adjust the earpads so that they cover your ears, otherwise
    noise canceling will not function properly.
    The noise canceling effect may vary depending on how
    you wear the headphones.
    Do not cover the microphone of the headphones with
    your hands. The noise canceling function may not work
    After you turn on the power of the headphones, you may
    hear a slight hiss. This is the operating sound of the noise
    canceling function, not a malfunction.
    The noise canceling function works for noise in the low
    frequency band primarily. Although noise is reduced, it is
    not canceled completely.
    The noise canceling effect may not be pronounced in a
    very quiet environment, or some noise may be heard.
    When you use the headphones in a train or a car, noise
    may occur depending on street conditions.
    Howling may occur if you do not wear the headphones
    Howling may occur if you place an object such as finger
    close to inside of the headphones. Keep it away from the
    Mobile phones may cause interference and noise. Should
    this occur, locate the headphones further away from the
    mobile phone.
    Notes on using on the airplane
    Do not use the headphones when use of electronic
    equipment is prohibited or when use of personal
    headphones for in-flight entertainment services is
    Notes on charging the headphones
    Charge the headphones using the supplied micro-USB
    cable. Otherwise, it may cause a malfunction.
    Charge in an environmental temperature of between 5°C
    and 35°C. Otherwise, the battery may not fully charge.
    Do not store the headphones in hot places for a long time.
    When storing it for more than a year, charge the battery
    once a year to prevent over discharge.
    For system requirements for a computer that can charge
    the battery using USB, see “System requirements for
    battery charge using USB”.
    If you recharge the headphones by connecting to an AC
    outlet, use the separately-sold USB AC Adaptor specific in
    “Recommended accessory (sold separately)”. For details,
    refer to the operating instructions supplied with the
    If the headphones are malfunctioning, charging will not
    start and the charging indicator will blink. In this case,
    disconnect the unit from the connected device, and
    consult your place of purchase, or a Sony dealer.
    Notes on handling
    Because the headphones are designed to fit closely in your
    ears, forcing them against your ears may result in eardrum
    damage. Avoid using the headphones where they are
    liable to be struck by people or other objects, such as a
    ball, etc.
    Pressing the headphones against your ears may produce a
    diaphragm click sound. This is not a malfunction.
    Clean the headphones with a soft dry cloth.
    Do not leave the plug dirty otherwise the sound may be
    Be sure to consult a Sony dealer when the earpads
    become dirty or damaged, or when the headphones
    require repair work.
    Do not leave the headphones in a location subject to
    direct sunlight, heat or moisture.
    Do not subject the headphones to excessive shock.
    Handle the driver units carefully.
    If you feel drowsy or sick while using this headphones,
    stop use immediately.
    Center button
    Bouton central
    Botón central
    Charging indicator
    Témoin de charge
    Indicador de recarga
    Micro-USB cable
    Micro-câble USB
    Cable micro-USB
    Tactile dot (on the left)
    Point tactile (à gauche)
    Punto táctil (a la
    Inline remote and microphone cord for iPod/iPhone/iPad
    Cordon du micro et distant en série pour iPod/iPhone/iPad
    Cable con control remoto y micrófono integrados para iPod/iPhone/iPad
    Notes on headphones
    High volume may affect your hearing. For traffic
    safety, do not use while driving or cycling.
    As headphones reduce outside sounds, they may cause a
    traffic accident. Also, avoid listening with your headphones
    in situations where hearing must not be impaired, for
    example, a railroad crossing, a construction site, etc.
    Note on static electricity
    In particularly dry air conditions, noise or sound skipping
    may occur, or mild tingling may be felt on your ears. This is a
    result of static electricity accumulated in the body, and not a
    malfunction of the headphones.
    The effect can be minimized by wearing clothes made from
    natural materials.
    If you have any questions or problems concerning the
    system that are not covered in this manual, please consult
    the nearest Sony dealer.
    No sound
    Recharge the headphones.
    You can listen to the music using the headphones even
    when the POWER switch is set to “OFF”. In this case, the
    noise canceling function, Digital Equalizer, S-Master and
    DSEE are not active, and the headphones operate as
    passive headphones.
    Check that the rechargeable battery is not depleted.
    Check the connection of the headphones and the
    Check that the connected equipment is turned on.
    Turn up the volume of the connected equipment.
    The noise canceling effect is not sufficient
    The noise canceling function is effective in low frequency
    ranges such as airplanes, trains, or offices (near air-
    conditioning, etc.) and is not as effective for higher
    frequencies, such as human voices.
    Turn on the headphones.
    Distorted sound
    Turn down the volume of the connected equipment.
    Recharge the headphones.
    Power does not turn on or the headphones
    do not operate properly
    Recharge the headphones.
    If the power does not turn on, even after charging the
    headphones, the rechargeable battery may be damaged.
    In this case, consult your place of purchase or a Sony
    Charging cannot be done
    Check that the charging indicator is lights up.
    Connect the headphones and the micro-USB cable
    Check that the micro-USB cable and the computer are
    firmly connected.
    Check that the micro-USB cable and the computer are
    directly connected; not via a USB hub.
    Check the system requirements for a computer that can
    charge the battery using USB.
    Check that the computer is turned on.
    Check that the computer is not in standby, sleep or
    hibernation mode.
    If the charging indicator blinks (blinking patterns: about 30
    seconds on and 3 seconds off), you are using an adaptor
    other than the recommended one. Use a USB AC Adaptor
    specified in “Recommended accessory (sold separately)”.
    If the charging indicator blinks, the headphones may be
    malfunctioning. Disconnect the unit from the connected
    device, and consult your place of purchase, or a Sony
    The unit cannot be recognized by a
    Check that the micro-USB cable and the computer are
    firmly connected.
    Disconnect the micro-USB cable from the computer and
    connect again.
    Check that the micro-USB cable and the computer are
    directly connected; not via a USB hub.
    There may be a problem with the connected USB port
    of the computer. Connect to another USB port if it is
    Try the USB connection procedure again in cases other
    than those stated above.
    No operation works
    Set the POWER switch of the headphones to “OFF”,
    confirm the connections, and then set the POWER switch
    back to “ON”.
    Reset the headphones.
    Insert a small pin, etc. into the RESET button on the left
    housing, and press until the button slightly rebounds.
    The connected iPod does not work
    Check if the cord is connected correctly. Connect
    the L type plug to the iPod and the other plug to the
    Digital Noise Canceling with Dual Noise Sensor
    Microphones both inside and outside the housings are
    combined with digital noise canceling software engine to
    deliver significant noise canceling performance.
    Automatic AI (Artificial Intelligence) Noise Canceling
    Automatic selection of the optimal noise canceling mode
    based on intelligent analysis of environmental ambient
    Digital Equalizer and full digital S-Master amplifier
    Delivers ideal frequency response and high-quality music
    reproduction with full digital processing.
    Offers natural sound with a spacious feel by restoring
    high-frequency range sound and the tail shape of the
    waveform likely to be removed through the audio
    compression process.
    Up to 22 hours of listening time
    Passive operation
    Allows audio listening even when the headphones power
    is turned off.
    Detachable cord
    Type Closed, dynamic
    Driver units 50 mm, dome type
    Power handling capacity
    100 mW
    Impedance 51 Ω at 1 kHz (when the power is on)
    19 Ω at 1 kHz (when the power is off)
    Sensitivity 103 dB/mW (when the power is on)
    100 dB/mW (when the power is off)
    Frequency response
    5 Hz – 24,000 Hz
    Total Noise Suppression Ratio
    Approx. 25 dB
    Power source DC 3.7 V Built-in lithium-ion rechargeable
    battery or DC 5 V USB
    Mass Approx. 330 g (11.7 oz) (without cord)
    Talk microphone Open circuit voltage level (Inline remote
    and microphone cord for iPod/iPhone/iPad)
    –42 dB (0 dB = 1 V/Pa)
    Headphones charging and usage time
    Approx. charging hours
    Approx. usage hours
    4 hours
    22 hours
    Included items
    Headphones (1)
    Inline remote and microphone cord for iPod/iPhone/iPad
    (1.2 m (47 1/4 in) cord, using PCOCC, four-conductor gold
    plated L-shaped stereo mini plug) (1)
    Micro-USB cable (1.5 m (59 1/8 in)) (1)
    Carrying case (1)
    Operating Instructions (1)
    Warranty card (1)
    Recommended accessory (sold separately)
    USB AC Adaptor: AC-UD20
    Under the Sony measurement standard.
    Equivalent to approx. 99.7% reduction of energy of sound
    compared with not wearing headphones.
    At 1 kHz, 0.1 mW + 0.1 mW output
    Hours required to fully charge an empty battery
    Time stated above may vary, depending on the
    temperature or conditions of use.
    Availability depends on the country.
    Design and specifications are subject to change without
    Compatible iPod/
    iPhone/iPad models
    You can use the headphones with only the following models
    supporting remote control. Update your iPod, iPhone or
    iPad to the latest software before use. In the Operating
    Instructions, iPod, iPhone and iPad are collectively described
    as “iPod” except in special cases.
    iPod touch (4th generation)
    iPod touch (3rd generation)
    iPod touch (2nd generation)
    iPod nano (6th generation)
    iPod nano (5th generation)
    iPod nano (4th generation)
    iPod classic 120GB 160GB (2009)
    iPod shuffle (4th generation)
    iPod shuffle (3rd generation)
    iPhone 4S
    iPhone 4
    iPhone 3GS
    iPad (3rd generation)
    iPad 2
    On copyright
    iPad, iPhone, iPod, iPod classic, iPod nano, iPod shuffle, and
    iPod touch are trademarks of Apple Inc., registered in the
    U.S. and other countries.
    “Made for iPod”, “Made for iPhone”, and “Made for iPad” mean
    that an electronic accessory has been designed to connect
    specifically to iPod, iPhone, or iPad, respectively, and has
    been certified by the developer to meet Apple performance
    standards. Apple is not responsible for the operation of this
    device or its compliance with safety and regulatory standards.
    System requirements
    for battery charge using
    Personal Computer with pre-installed with any of the
    following operating systems and USB port:
    Operating Systems
    When using Windows®
    Windows® 7
    (Home Premium / Professional / Ultimate / Starter)
    (including 64 bit version)
    Windows Vista® (Service Pack 2 or later)
    (Home Basic / Home Premium / Business / Ultimate)
    (including 64 bit version)
    Windows® XP (Service Pack 3 or later)
    (Home Edition / Professional / Media Center Edition 2004 /
    Media Center Edition 2005)
    When using Macintosh
    Mac OS X (version.10.5 or later)
    Windows and Windows Vista are registered trademarks or
    trademarks of Microsoft Corporation in the United States
    and/or other countries.
    Macintosh and Mac OS are trademarks of Apple Inc.,
    registered in the U.S. and other countries.
    Noise Canceling
    Operating Instructions
    Mode d’emploi
    Manual de instrucciones
    L indication
    Indication L
    Indicación L
    R indication
    Indication R
    Indicación R

Ho bisogno di aiuto?

Numero di domande: 0

Hai domande sul Sony MDR-1RNC o hai bisogno di aiuto? Fai qui la tua domanda. Fornisci una descrizione chiara e completa del problema e della domanda. Più dettagli fornisci per il tuo problema e la tua domanda, più facile sarà per gli altri proprietari di Sony MDR-1RNC rispondere correttamente alla tua domanda.

Consulta qui gratuitamente il manuale per il Sony MDR-1RNC. Il manuale rientra nella categoria Cuffia ed è stato valutato da 1 persone con una media di 8. Il manuale è disponibile nelle seguenti lingue: Inglese, Francese, Spagnolo. Hai domande sul Sony MDR-1RNC o hai bisogno di aiuto? Fai la tua domanda qui

Specifiche Sony MDR-1RNC

Marca Sony
Modello MDR-1RNC
Prodotto Cuffie
EAN 4905524858938
Lingua Inglese, Francese, Spagnolo
Tipo di file PDF
- Circumaurale
- Padiglione auricolare
- 100
- 5 - 24000
- 103
- 52
- 50
- Neodimio
- closed
- Cablato
- -
- 1.2
- Oro
- 330
- 22
- 4
- Nero
- Micro-USB
- LCP 40mm
- iPod/iPhone/iPad
- Dinamico
- Cuffie
Sensibilità cuffia 103
Impedenza 52
Unità driver 50
Tipo di magnete Neodimio
Sistema acustico closed
Tipologia driver Dinamico
Massima potenza in entrata 100
Frequenza cuffia 5 - 24000
Disegno auricolare Circumaurale
Durata batteria 22
Tempo di ricarica 4
Lunghezza cavo 1.2
Colore del prodotto Nero
Controllo del volume
Stile d'uso Padiglione auricolare
Tipo di prodotto Cuffie
Utilizzo raccomandato Chiamate e musica
Altre caratteristiche
Spinotto adattatore Micro-USB
Diaframma LCP 40mm
Compatibilità iPod/iPhone/iPad
Placcatura contatti Oro
Tecnologia di connessione Cablato
Dimensioni e peso
Peso 330
Effetto di cancellazione del rumore
Tipo di microfono In linea

Domande frequenti

Di seguito, troverai le domande più frequenti riguardo Sony MDR-1RNC .

La tua domanda non è elencata? Fai la tua domanda qui


Stai cercando un manuale? ManualeD' farà in modo che tu possa trovare il manuale che stai cercando in un attimo. Il nostro database contiene più di 1 milione di manuali in formato PDF di oltre 10.000 marchi. Ogni giorno aggiungiamo i manuali più recenti in modo che sia sempre possibile trovare il prodotto che stai cercando. È molto semplice: basta digitare il marchio e il tipo di prodotto nella barra di ricerca e immediatamente visualizzerai gratuitamente il manuale di tua scelta online.


© Copyright 2020 ManualeD' Tutti I diritti riservati.

Utilizziamo i cookie per essere sicuri che tu possa avere la migliore esperienza sul nostro sito. Se continui ad utilizzare questo sito noi assumiamo che tu ne sia felice.

Leggi di più