Sony SNC-CH120 manuale

Sony SNC-CH120
  • Numero di pagine: 2
  • Tipo di file: PDF
4-199-272-13 (1)

Network Camera

Installation Manual
Before operating the unit, please read this manual thoroughly and retain it for future reference.


Owner’s Record

The model and serial numbers are located on the top. Record these numbers in the spaces provided below.Refer to these numbers whenever you call upon your Sony dealer regarding this product.Model No. Serial No.


To reduce a risk of fire or electric shock, do not expose this product to rain or moisture.To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only. WARNINGThis installation should be made by a qualified service person and should conform to all local codes.WARNINGA readily accessible disconnect device shall be incorporated in the building installation wiring.WARNING (for Installers only)Instructions for installing the equipment on the ceiling or the wall:After the installation, ensure the connection is capable of supporting at least a force of 50 Newtons (N) downwards.CAUTION for LAN portFor safety reason, do not connect the LAN port to any network devices that might have excessive voltage.The LAN port of this unit is to be connected only to the devices whose power feeding meets the requirements for SELV (Safety Extra Low Voltage) and complies with Limited Power Source according to IEC 60950-1.Use IEEE802.3af standard compliant devices.For customers in the U.S.A.This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment.All interface cables used to connect peripherals must be shielded in order to comply with the limits for a digital device pursuant to Subpart B or Part 15 of FCC Rules.For customers in CanadaThis Class A digital apparatus complies with Canadian ICES-003.Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.For the customers in EuropeThe manufacturer of this product is Sony Corporation, 1-7-1 Konan, Minato-ku, Tokyo, Japan.The Authorized Representative for EMC and product safety is Sony Deutschland GmbH, Hedelfinger Strasse 61, 70327 Stuttgart, Germany. For any service or guarantee matters please refer to the addresses given in separate service or guarantee documents.For the customers in Europe, Australia and New ZealandWARNINGThis is a Class A product. In a domestic environment, this product may cause radio interference in which case the user may be required to take adequate measures.In the case that interference should occur, consult your nearest authorized Sony service facility.This apparatus shall not be used in the residential area.ATTENTIONThe electromagnetic fields at specific frequencies may influence the picture of the unit.
Notes on Use
Before UseIf you find condensation when you open the package, turn on the power after the condensation disappears.Remove the static electricity before operation or when touching the camera.Data and securityYou should keep in mind that the images or audio you are monitoring may be protected by privacy and other legal rights, and the responsibility for making sure you are complying with applicable laws is yours alone. Access to the images and audio is protected only by a user name and the password you set up. No further authentication is provided nor should you presume that any other protective filtering is done by the service. Since the service is Internet-based, there is a risk that the image or audio you are monitoring can be viewed or used by a third-party via the network.SONY IS NOT RESPONSIBLE, AND ASSUMES ABSOLUTELY NO LIABILITY TO YOU OR ANYONE ELSE, FOR SERVICE INTERRUPTIONS OR DISCONTINUATIONS OR EVEN SERVICE CANCELLATION. THE SERVICE IS PROVIDED AS-IS, AND SONY DISCLAIMS AND EXCLUDES ALL WARRANTIES, EXPRESS OR IMPLIED, WITH RESPECT TO THE SERVICE INCLUDING, BUT NOT LIMITED TO, ANY OR ALL IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR THAT IT WILL OPERATE ERROR-FREE OR CONTINUOUSLY.Always make a test recording, and verify that it was recorded successfully. SONY WILL NOT BE LIABLE FOR DAMAGES OF ANY KIND INCLUDING, BUT NOT LIMITED TO, COMPENSATION OR REIMBURSEMENT ON ACCOUNT OF FAILURE OF THIS UNIT OR ITS RECORDING MEDIA, EXTERNAL STORAGE SYSTEMS OR ANY OTHER MEDIA OR STORAGE SYSTEMS TO RECORD CONTENT OF ANY TYPE.Always verify that the unit is operating properly before use. SONY WILL NOT BE LIABLE FOR DAMAGES OF ANY KIND INCLUDING, BUT NOT LIMITED TO, COMPENSATION OR REIMBURSEMENT ON ACCOUNT OF THE LOSS OF PRESENT OR PROSPECTIVE PROFITS DUE TO FAILURE OF THIS UNIT, EITHER DURING THE WARRANTY PERIOD OR AFTER EXPIRATION OF THE WARRANTY, OR FOR ANY OTHER REASON WHATSOEVER.If you lose data by using this unit, SONY accepts no responsibility for restoration of the data.Personal informationThe images taken by the system using this device can identify individuals and thus they fall under “personal information” stipulated in the “Act on the Protection of Personal Information”. Please handle the video data appropriately according to law.Information recorded using this product may also be “personal information”. Upon disposal, transfer, repair, or any other occasion where this product or storage media is passed on to a third party, practice due care in its handling.Operating or storage locationAvoid operating or storing the camera in the following locations.Extremely hot or cold places (Operating temperature: 10°C to +50°C [14°F to 122°F])Exposed to direct sunlight for a long time, or close to heating equipment (e.g., near heaters)Close to sources of strong magnetismClose to sources of powerful electromagnetic radiation, such as radios or TV transmittersLocations subject to strong vibration or shockHumid or dusty locationsLocations exposed to rainLocations under the influence of fluorescent light or reflection of a windowUnder an unsteady light (The image will flicker.)VentilationTo prevent heat buildup, do not block air circulation around the camera.Power supplyThe power of this model is supplied by network cable.Use the network cable UTP, category-5.Damage to the network cable may result in fire or electric shock.TransportationAlways turn off the power when carrying.When transporting the camera, repack it as originally packed at the factory or in materials of equal quality.CleaningUse a blower to remove dust from the lens.Use a soft, dry cloth to clean the external surfaces of the camera. Stubborn stains can be removed using a soft cloth dampened with a small quantity of detergent solution, then wipe dry.Do not use volatile solvents such as alcohol, benzene or thinners as they may damage the surface finishes.Note on laser beamsLaser beams may damage image sensors. You are cautioned that the surface of image sensors should not be exposed to laser beam radiation in an environment where a laser beam device is used.
Phenomena Specific to Image Sensors
The following phenomena that may occur in images are specific to image sensors. They do not indicate a malfunction.White flecksAlthough the image sensors are produced with high-precision technologies, fine white flecks may be generated on the screen in rare cases, caused by cosmic rays,
This is related to the principle of image sensors and is not a malfunction.The white flecks especially tend to be seen in the following cases:- when operating at a high environmental temperature- when you have raised the gain (sensitivity)- when using the slow shutterAliasingWhen fine patterns, stripes, or lines are shot, they may appear jagged or flicker.
About the imaging conditions
When Auto Iris is set to On, resolution may be unsatisfactory. In this case, set Auto Iris to Off.
About the Supplied Manuals
Installation Manual (this document)This Installation Manual describes the names and functions of parts and controls of the Network Camera, gives connection examples and explains how to set up the camera. Be sure to read the Installation Manual before operating.User’s Guide (stored in the CD-ROM)The User’s Guide describes how to set up the camera and how to control the camera via a Web browser.After installing and connecting the camera correctly, operate referring to this User’s Guide.
Using the CD-ROM Manuals
The supplied CD-ROM disc includes the User’s Guides for this unit in PDF format.PreparationsThe Adobe Reader Version 6.0 or higher must be installed on your computer in order to use the guides stored in the CD-ROM disc. Note If Adobe Reader is not installed, it may be downloaded from the following URL: the manual in the CD-ROM
1 Insert the CD-ROM in your CD-ROM drive.
A cover page appears automatically in your Web browser. If it does not appear automatically in the Web browser, double-click on the index.htm file on the CD-ROM.
2 Select and click on the manual that you want to read.
This opens the PDF file of the manual. Clicking an item in the Table of Contents allows you jump to the relevant page.Notes The files may not be displayed properly, depending on the version of Adobe Reader. In this case, install the latest version, which you can download from the URL mentioned in “Preparations” above.If you have lost or damaged the CD-ROM, you can purchase replacement. Contact your Sony service representative.Adobe and Acrobat Reader are trademarks of Adobe Systems Incorporated in the United States and/or other countries.
Location and Function of Part
LensA vari-focal lens is mounted as standard equipment. Focus ringTurn this ring toward N (near) to focus on a closer object. Turn it toward F (infinite) to focus on a farther object. Zoom ringTurn this ring toward T for telephoto, or toward W for wide-angle. Tripod screw holeUse this screw hole when attaching the camera to a tripod (screw: 1/4”, 20 UNC). You can attach a tripod to either the top or bottom of the camera.CautionUse the mounting screw whose length is 4.5 mm (
/ inch) – 7 mm
/ inch) only. Use of other screws may cause improper mounting and damage parts inside the camera. Rating LabelThis label shows the name of device and its electric rating. Lens connector (4-pin socket)Supplies power and control signals to an auto-iris lens.
I/O (Input/Output) portThis cable is provided with a sensor input and an alarm output.The wires of the cable control the following signals.PinNo. Signal1 Alarm output 1–2 Alarm output 1+3 Sensor input– (GND)4 Sensor input+ For details on each function and required settings, see the User’s Guide stored in the supplied CD-ROM. For the wiring, see “Connecting the I/O cable.” LAN network port (RJ-45)Use the network cable (UTP, category-5) for network communications and PoE* power supply. See “Connect to the Network” for connection.(* PoE: The acronym for Power over Ethernet. IEEE 802.3af standard compliant devices.) Easy Focus buttonPress this button to automatically adjust the focus.To load the default setting, press and hold this button for 4 seconds. Fall-prevention wire rope mounting screw holeWhen installing the camera to the ceiling or the wall, secure the supplied wire rope to this hole using the supplied screw. NETWORK indicator (Green/Orange)The indicator lights up or flashes when the camera is connected to the network. The indicator is off when the camera is not connected to the network. When 100BASE-TX is connected, the indicator turns green. When 10BASE-T is connected, the indicator turns orange. Reset switchTo reset the camera to the factory default settings, turn on the power to the camera while holding down this switch with a pointed object. POWER indicator (Green)When the power is supplied to the camera, the camera starts checking the system. If the system is normal, this indicator lights up. NTSC/PAL switchSwitching the video output. MONITOR output jackOutput the composite video signal from the camera.Monitor out is used when you adjust the angle of view. Be sure to set monitor out to on when you use it. Set it to off and disconnect the video cable when you do not use it.For details on system setting, see the User’s Guide.NotesDo not connect to the video cable until the POWER indicator lights
Be aware that the system performance may be influenced, if monitor out is set to on. Be sure to set it to off and disconnect the video cable when you do not use it.
(continued on the reverse side)
2010 Sony Corporation Printed in China
U1/4”, 20 UNC = 4.5 mm - 7 mm(ISO standard) (with thescrews fastened)
Sony SNC-CH120

Ho bisogno di aiuto?

Numero di domande: 0

Hai domande sul Sony SNC-CH120 o hai bisogno di aiuto? Fai qui la tua domanda. Fornisci una descrizione chiara e completa del problema e della domanda. Più dettagli fornisci per il tuo problema e la tua domanda, più facile sarà per gli altri proprietari di Sony SNC-CH120 rispondere correttamente alla tua domanda.

Consulta qui gratuitamente il manuale per il Sony SNC-CH120. Il manuale rientra nella categoria Telecamera di sorveglianza ed è stato valutato da 1 persone con una media di 7. Il manuale è disponibile nelle seguenti lingue: Inglese. Hai domande sul Sony SNC-CH120 o hai bisogno di aiuto? Fai la tua domanda qui

Specifiche Sony SNC-CH120

Marca Sony
Modello SNC-CH120
Prodotto Telecamere di sorveglianza
EAN 132017628097, 27242260580
Lingua Inglese
Tipo di file PDF
Formati video supportati H.264
Risoluzione massima 1329 x 1049 Pixel
Frame rate 20/30, 30 fps
Macchina fotografica
Angolo di visualizzazione (orizzontale) 96.5 °
Velocità otturatore 1 - 1/10000 s
Bilanciamento del bianco Auto,Manual
Illuminazione min. 0.5 lx
Sensore d'immagine
Tipo sensore CMOS
Sistema di lente
Lunghezza focale 2.8 - 8 mm
Zoom ottico 2.9 x
Collegamento in rete
Protocolli di rete supportati IPv4, IPv6, TCP, UDP, ARP, ICMP, IGMP, HTTP, HTTPS, FTP (client only), SMTP, DHCP, DNS,NTP, RTP/RTCP, RTSP, SNMP (MIB-2)
Wi-Fi No
Altre caratteristiche
Alimentazione PoE (IEEE802.3af compliant)
Dimensioni (LxPxA) 72 x 63 x 197 mm
Sistema operativo compatibile Microsoft Windows XP/ Vista(32bit)/ 7(32bit)
Numero F (apertura relativa) F1.2, F1.9
Gestione energetica
Supporto Power over Ethernet (PoE) -
Consumi 5 W
Interfaccia -
Veduta notturna
Visione notturna
Dimensioni e peso
Peso 550 g
Condizioni ambientali
Intervallo temperatura di funzionamento -10 - 50 °C
Intervallo di temperatura -20 - 60 °C
Requisiti di sistema
Processore minimo Intel Core2 Duo 2 GHz
RAM minima 1024 MB
Mostra di più

Domande frequenti

Di seguito, troverai le domande più frequenti riguardo Sony SNC-CH120 .

La tua domanda non è elencata? Fai la tua domanda qui