Sony SNC-DH260 manuale

Sony SNC-DH260
(1)
  • Numero di pagine: 2
  • Tipo di file: PDF
4-258-903-13 (1)

Network Camera

Installation Manual
Before operating the unit, please read this manual thoroughly and retain it for future reference.

Owner’s Record

The model and serial numbers are located on the bottom. Record these numbers in the spaces provided below.Refer to these numbers whenever you call upon your Sony dealer regarding this product.Model No. Serial No.

WARNING

To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only. WARNINGThis installation should be made by a qualified service person and should conform to all local codes.WARNING (for Installers only)Instructions for installing the equipment on the ceiling or the wall:After the installation, ensure the connection is capable of supporting five times the weight of the equipment downwards.CAUTIONThe rating label is located on the bottom.CAUTION for LAN portFor safety reason, do not connect the LAN port to any network devices that might have excessive voltage.The LAN port of this unit is to be connected only to the devices whose power feeding meets the requirements for SELV (Safety Extra Low Voltage) and complies with Limited Power Source according to IEC 60950-1.Power SupplyUse IEEE802.3af standard compliant devices.Caution for U.S.A. and CanadaIn the USA, this product shall be powered by a UL listed Class 2 Power Supply Only.In Canada, this product shall be powered by a CSA Certified Class 2 Power Supply Only.For customers in the U.S.A.This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment.All interface cables used to connect peripherals must be shielded in order to comply with the limits for a digital device pursuant to Subpart B or Part 15 of FCC Rules.For customers in CanadaThis Class A digital apparatus complies with Canadian ICES-003.Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.For the customers in EuropeThe manufacturer of this product is Sony Corporation, 1-7-1 Konan, Minato-ku, Tokyo, Japan.The Authorized Representative for EMC and product safety is Sony Deutschland GmbH, Hedelfinger Strasse 61, 70327 Stuttgart, Germany. For any service or guarantee matters please refer to the addresses given in separate service or guarantee documents.For the customers in Europe, Australia and New ZealandWARNINGThis is a Class A product. In a domestic environment, this product may cause radio interference in which case the user may be required to take adequate measures.In the case that interference should occur, consult your nearest authorized Sony service facility.This apparatus shall not be used in the residential area.ATTENTIONThe electromagnetic fields at specific frequencies may influence the picture of the unit.
Notes on Use
Before UseDo not lift the camera by only holding the cables.If you find condensation when you open the package, turn on the power after leaving it for about 60 minutes.Remove static electricity before installation and operation.Data and securityYou should keep in mind that the images or audio you are monitoring may be protected by privacy and other legal rights, and the responsibility for making sure you are complying with applicable laws is yours alone. Access to the images and audio is protected only by a user name and the password you set up. No further authentication is provided nor should you presume that any other protective filtering is done by the service. Since the service is Internet-based, there is a risk that the image or audio you are monitoring can be viewed or used by a third-party via the network.SONY IS NOT RESPONSIBLE, AND ASSUMES ABSOLUTELY NO LIABILITY TO YOU OR ANYONE ELSE, FOR SERVICE INTERRUPTIONS OR DISCONTINUATIONS OR EVEN SERVICE CANCELLATION. THE SERVICE IS PROVIDED AS-IS, AND SONY DISCLAIMS AND EXCLUDES ALL WARRANTIES, EXPRESS OR IMPLIED, WITH RESPECT TO THE SERVICE INCLUDING, BUT NOT LIMITED TO, ANY OR ALL IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR THAT IT WILL OPERATE ERROR-FREE OR CONTINUOUSLY.Security configuration is essential for wireless LAN. Should a problem occur without setting security, or due to the limitation of the wireless LAN specifications, SONY shall not be liable for any damage, loss of recorded data or restoration thereof.Always make a test recording, and verify that it was recorded successfully. SONY WILL NOT BE LIABLE FOR DAMAGES OF ANY KIND INCLUDING, BUT NOT LIMITED TO, COMPENSATION OR REIMBURSEMENT ON ACCOUNT OF FAILURE OF THIS UNIT OR ITS RECORDING MEDIA, EXTERNAL STORAGE SYSTEMS OR ANY OTHER MEDIA OR STORAGE SYSTEMS TO RECORD CONTENT OF ANY TYPE.Always verify that the unit is operating properly before use. SONY WILL NOT BE LIABLE FOR DAMAGES OF ANY KIND INCLUDING, BUT NOT LIMITED TO, COMPENSATION OR REIMBURSEMENT ON ACCOUNT OF THE LOSS OF PRESENT OR PROSPECTIVE PROFITS DUE TO FAILURE OF THIS UNIT, EITHER DURING THE WARRANTY PERIOD OR AFTER EXPIRATION OF THE WARRANTY, OR FOR ANY OTHER REASON WHATSOEVER.If you lose data by using this unit, SONY accepts no responsibility for restoration of the data.Personal informationThe images taken by the system using this device can identify individuals and thus they fall under “personal information” stipulated in the “Act on the Protection of Personal Information”. Please handle the video data appropriately according to law.Information recorded using this product may also be “personal information”. Upon disposal, transfer, repair, or any other occasion where this product or storage media is passed on to a third party, practice due care in its handling.Operating or storage locationAvoid operating or storing the camera in the following locations.Extremely hot or cold places (Operating temperature: –30°C to +50°C [–22°F to +122°F])Close to heating equipment (e.g., near heaters)Close to sources of strong magnetismClose to sources of powerful electromagnetic radiation, such as radios or TV transmittersLocations subject to strong vibration or shockDon’t touch the PCB board by hand directly.If the camera do not focus well because of the weather (such as rain), adjust the focus manually.VentilationTo prevent heat buildup, do not block air circulation around the camera.TransportationAlways turn off the power when carrying.When transporting the camera, repack it as originally packed at the factory or in materials of equal quality.Using in cold climatesThis device is equipped with a built-in heater which automatically operates when the internal temperature drops significantly low. However, the heater may not defrost snow and frost attached on the dome cover under certain environment condition.Starting and closing under low temperatureWhen started under temperature conditions of 0°C (32°F) or below, the camera system may not start operating immediately after start-up. In such a case, the heater and the IR LED starts and raises the internal temperature, starting the camera system. It may take about one hour for the camera system to start streaming normal images.CleaningUse a blower to remove dust from the lens.Use a soft, dry cloth to clean the external surfaces of the camera. Stubborn stains can be removed using a soft cloth dampened with a small quantity of detergent solution, then wipe dry.Do not use volatile solvents such as alcohol, benzene or thinners as they may damage the surface finishes.To install the camera outdoorsAttach the dome casing securely to the unit casing.Make sure you seal the locations listed below with sealant (e.g. silicon sealant) to prevent moisture from getting inside the casing. It is better to install the camera in a environment of low humidity.Camera installation holes (4)Conduit holes (side/bottom)Note on laser beamsLaser beams may damage image sensors. You are cautioned that the surface of image sensors should not be exposed to laser beam radiation in an environment where a laser beam device is used.
Phenomena Specific to Image Sensors
The following phenomena that may occur in images are specific to image sensors. They do not indicate a malfunction.White flecksAlthough the image sensors are produced with high-precision technologies, fine white flecks may be generated on the screen in rare cases, caused by cosmic rays,
etc.
This is related to the principle of image sensors and is not a malfunction.The white flecks especially tend to be seen in the following cases:- when operating at a high environmental temperature- when you have raised the gain (sensitivity)- when using the slow shutterAliasingWhen fine patterns, stripes, or lines are shot, they may appear jagged or flicker.
About the Supplied Manuals
Installation Manual (this document)This Installation Manual describes the names and functions of parts and controls of the Network Camera, gives connection examples and explains how to set up the camera. Be sure to read the Installation Manual before operating.User’s Guide (stored in the CD-ROM)The User’s Guide describes how to set up the camera and how to control the camera via a Web browser.After installing and connecting the camera correctly, operate referring to this User’s Guide.
Using the CD-ROM Manuals
The supplied CD-ROM disc includes the User’s Guides for this unit in PDF format.PreparationsThe Adobe Reader Version 6.0 or higher must be installed on your computer in order to use the guides stored in the CD-ROM disc. Note If Adobe Reader is not installed, it may be downloaded from the following URL: http://www.adobe.com/Reading the manual in the CD-ROM
1 Insert the CD-ROM in your CD-ROM drive.
A cover page appears automatically in your Web browser. If it does not appear automatically in the Web browser, double-click on the index.htm file on the CD-ROM.
2 Select and click on the manual that you want to read.
This opens the PDF file of the manual. Clicking an item in the Table of Contents allows you jump to the relevant page.Notes The files may not be displayed properly, depending on the version of Adobe Reader. In this case, install the latest version, which you can download from the URL mentioned in “Preparations” above.If you have lost or damaged the CD-ROM, you can purchase replacement. Contact your Sony service representative.Adobe and Acrobat Reader are trademarks of Adobe Systems Incorporated in the United States and/or other countries.
Location and Function of Part
The figure shows the camera without the dome casing.
Side
Cable is not connected when the unit comes from the factory. I/O (Input/Output) cable (supplied)This cable is provided with a sensor input and two alarm outputs.The wires of the cable control the following signals.Color of wire NameRed Sensor In +White Sensor In – (GND)Black Alarm Out 1 +Yellow Alarm Out 1 –Brown Not usedGreen Not usedFor details on each function and required settings, see the User’s Guide stored in the supplied CD-ROM.For the wiring, see “Connecting the I/O cable.” Wiring slitFeed the wire rope through this.For details, see “Installing the Camera” on the reverse side. Camera head holder Lens LAN cable (RJ-45) (supplied and connected to the camera at the factory)Connect this cable to a hub or computer on the 10BASE-T or 100BASE-TX network using a network cable (UTP, category 5). Conduit holes (
3
/
4
inch)Connect a pipe to this hole. There are two conduit holes on the unit casing, one on the side and one at the bottom. The cover plug is installed in the side conduit hole at the factory. Remove the plug as needed and connect the pipe to the hole.
Note
Take care not to trap the cables between the camera and the ceiling or the wall. If the cable is trapped, it may cause a fire or electric shock due to breaking. IR LED
Inside
Camera unit Easy Focus buttonPress this button to automatically adjust the focus easily. Camera head fixing screwFirst loosen the screw and face the camera head to the desired direction, then tighten the screw to fix it. ZOOM/FOCUS switchUse this switch to adjust lens’zoom and focus. Slide the switch lever toselect the desired function.[W] WIDE: Zoom out[T] TELE: Zoom in[N] NEAR: Focus on a nearby subject[F] FAR: Focus on a distant subject LAN portConnect the supplied LAN cable. Reset switchTo reset the camera to the factory default settings, hold down this switch with a point and supply the power to the camera. Camera installation hole (4 positions)Make sure to tighten the screws securely when installing the camera. Heater indicator (Green)The indicator lights up when the heater is active. NTSC/PAL switchSwitching the video output. POWER indicator (Green)When power is supplied to the camera, the camera starts checking the system. If the system is normal, this indicator lights up. NETWORK indicator (Green/Orange)The indicator lights up or flashes when the camera is connected to the network. The indicator is off when the camera is not connected to the network. When 100BASE-TX is connected, the indicator turns green. When 10BASE-T is connected, the indicator turns orange. MONITOR output jackConnect this jack to a video input connector of a video monitor. You can adjust the camera or lens while looking at the image on the video monitor. After adjusting the camera or lens, disconnect the cable. EXT CTRL (external control input/output) connectorConnect the supplied I/O cable to this connector. Safety cordThis cord prevents the dome casing from falling off the unit casing. Dome casingThe dome cover is made of polycarbonate. A waterproof rubber gasket is provided on the joint surface to the unit casing.(continued on the reverse side)
2010 Sony Corporation Printed in China

SNC-DH160/DH260

Sony SNC-DH260

Ho bisogno di aiuto?

Numero di domande: 0

Hai domande sul Sony SNC-DH260 o hai bisogno di aiuto? Fai qui la tua domanda. Fornisci una descrizione chiara e completa del problema e della domanda. Più dettagli fornisci per il tuo problema e la tua domanda, più facile sarà per gli altri proprietari di Sony SNC-DH260 rispondere correttamente alla tua domanda.

Consulta qui gratuitamente il manuale per il Sony SNC-DH260. Il manuale rientra nella categoria Telecamera di sorveglianza ed è stato valutato da 1 persone con una media di 7.5. Il manuale è disponibile nelle seguenti lingue: Inglese. Hai domande sul Sony SNC-DH260 o hai bisogno di aiuto? Fai la tua domanda qui

Specifiche Sony SNC-DH260

Generale
Marca Sony
Modello SNC-DH260
Prodotto Telecamere di sorveglianza
EAN 27242809604
Lingua Inglese
Tipo di file PDF
Video
Risoluzione massima 1920 x 1440 Pixel
Formati video supportati H.264,MPEG4
Risoluzioni grafiche supportate 720 x 480,720 x 576,1280 x 960,1920 x 1440,1024 x 768 (XGA),1280 x 1024 (SXGA),1280 x 720 (HD 720),1600 x 1200 (UXGA),1920 x 1080 (HD 1080),640 x 480 (VGA)
Modalità video supportate 1080p
Formato video analogico NTSC,PAL
Frame rate 30 fps
Megapixel totali 3.27 MP
Macchina fotografica
Illuminazione min. 0.5 lx
Angolo di visualizzazione (orizzontale) 88.5 °
Bilanciamento del bianco Auto,Manual
Tipo di otturatore Elettronico
Velocità otturatore 1 - 1/10000 s
Sensore d'immagine
Tipo sensore CMOS
Dimensioni sensore ottico 1/2.8 "
Risoluzione sensori effettiva 3270000 Pixel
Scansione progressiva
Sistema di lente
Zoom ottico 2.9 x
Lunghezza focale 3.1 - 8.9 mm
Sicurezza
Riconoscimento movimento video
Algoritmi di sicurezza supportati 802.1x RADIUS
Archiviazione
Disco rigido integrato No
Lettore di schede integrato No
Veduta notturna
Visione notturna
Distanza di visione notturna 15 m
Tipo LED IR
Numero di LED 50
Lunghezza d'onda a infrarossi 850 nm
Design
Fattore di forma Cupola
Colore del prodotto Bianco
Codice di protezione internazionale (IP) IP66
Prestazione
Controllo PTZ -
Posizionamento supportato -
Modalità giorno/notte
Tecnologia di connessione Cablato
Certificazione IK10\nUL2044, FCC 15B Class A, IC Class A, IEC60950-1, EN55022(A)+EN55024+EN50130-4, VCCI Class A, C-Tick Class A
Ingresso/uscita allarme
Contenuto dell'imballo
Software forniti ONVIF
Manuale dell'utente
Connettività
Quantità porte Ethernet LAN (RJ-45) 1
Porte RS-422 0
Porte RS-485 0
Uscite per cuffie 0
Collegamento in rete
Collegamento ethernet LAN
Tecnologia di cablaggio 10/100Base-T(X)
Wi-Fi No
Protocolli di rete supportati IPv4, IPv6, TCP, UDP, ARP, ICMP, IGMP, HTTP, HTTPS, FTP, SMTP, DHCP, DNS,NTP, RTP/RTCP, RTSP, SNMP
Dimensioni e peso
Larghezza 166 mm
Profondità 166 mm
Altezza 119 mm
Peso 1320 g
Gestione energetica
Supporto Power over Ethernet (PoE)
Consumi 12.9 W
Tipologia alimentazione PoE
Condizioni ambientali
Intervallo temperatura di funzionamento -30 - 50 °C
Intervallo di temperatura -20 - 60 °C
null
Requisiti di sistema
Processore minimo Intel Core2 Duo 2 GHz
Altre caratteristiche
Sistema operativo compatibile Windows XP/Vista (32bit)/ 7 (32bit)
Mostra di più

Domande frequenti

Di seguito, troverai le domande più frequenti riguardo Sony SNC-DH260 .

La tua domanda non è elencata? Fai la tua domanda qui