Stanley S200

Stanley S200 manuale

(1)
  • REV A 08STHT77406
    S200
    1
    2
    10
    8
    8
    2 3 6 7
    3 sec
    10
    4 5
    1
    77406
    Stanley Stud Sensor 200
    The Stud Sensor 200 uses electronic signals to locate the center of
    studs, joists or live AC wires through drywall or other common building
    materials. Once the center of a stud has been detected in one pass
    across the surface, the Stud Sensor 200 gives a visual display and
    sounds an audible tone. A marking channel allows you to easily note
    the stud center and edges on the wall.
    Note: Read all instructions prior to operating the Stud Sensor 200 and
    DO NOT remove any labels from the tool.
    WARNING:
    Protect Your Eyes, Wear Safety Goggles.
    Usage
    Detecting Wood / Metal Studs
    2
    Hold the Stud Sensor 200 fl at
    against the surface, making fi rm
    contact.
    3
    Press in and hold the activation
    button. A series of tones will
    sound.
    Note: The unit cannot be moved
    before calibration is complete.
    6
    /
    7
    When it detects the stud
    center, the “Center” icon will
    appear on the LCD and an audible
    tone will sound. Use the marking
    channel located at the top of the
    unit to mark the stud center.
    OPERATING INSTRUCTIONS
    Battery
    1
    Open door on back of unit and connect a 9 volt
    battery (not included) to clip. Put battery back into
    case and close back battery door.
    Note: Recommend to replace a new 9 volt
    battery when low battery - “Low Battery” will
    appear on the LCD.
    10
    If all segments of the LCD fl ash on and off
    when the activation button is pressed, move the
    Stud Sensor 200 to a different location and try
    again. Releasing the activation button will turn
    off the sensor.
    Note: While calibrating, the Stud Sensor 200
    must not be placed directly over a stud, dense
    material such as metal, or over a wet or newly
    painted area, or it will not properly calibrate.
    8
    Slide the Stud Sensor 200 slowly across the surface in a straight
    line. As it detects a stud, the unit will display the relative position
    of the stud on the screen.
    • Marking Channel
    Live Wire Warning LED
    • LCD Display
    • Activation Button
    Live Wire Detected
    Low Battery Indicator
    • Self-Calibration Complete
    Stud Location Graphic
    4
    When the unit is calibrated the
    “Ready” icon will appear on the
    LCD.
    5
    Keep holding the activation
    button during all of the following
    procedures.
    Note: Once the Activation button
    is released, the unit shuts off.

Vuoi sapere di Stanley S200?

manual_questions_numberofquestions 0

Chiedi la domanda che hai sul Stanley S200 semplimente ad altri proprietari di prodotto qui. Assicurati di fornire una descrizione chiara ed asauriente del problema e della tua domanda. Migliore è la descrizione del tuo problema e della domanda, più facile è per gli altri proprietari del Stanley S200 fornirti una buona risposta.

Visualizza qui il manuale gratuito del Stanley S200. Hai letto il manuale, ma risponde alla tua domanda? Quindi fai la tua domanda su questa pagina ad altri proprietari del Stanley S200

Specifiche

Marca Stanley
Modello S200
Prodotto Non classificato
EAN 3253560774066, 0604310238445
Lingua Italiano, Olandese, Finlandese, Sloveno, Ungherese, Greco, Slovacco, Turco, Rumeno, Ceco, Russo, Norvegese, Inglese, Polacco, Danese, Portoghese, Svedese, Spagnolo, Francese, Tedesco, Croato
Tipo di file PDF

In vendita su

    Relaterade produkter

    Non classificato Stanley

    manual_uploadmanual_title

    manual_uploadmanual_description