Vivanco UR 850 LCD

Vivanco UR 850 LCD manuale

(1)
  • UR 850 LCD Universal Controller
    Vivanco GmbH, Ewige Weide 15, D-22926 Ahrensburg, e-Mail: hotline@vivanco.de 1
    (GB) Operating Instructions
    Vivanco UR 850 LCD remote control for
    practically all TV, audio, video and other
    infrared-controllable devices
    Inserting the batteries
    Open the battery compartment on the back of the
    device, push the flap down lightly and insert 2 AA
    alkaline batteries. Make sure that the polarity on the
    batteries and in the battery compartment correspond
    (thick spring = cell at bottom = -) and then close the
    lid carefully. – Use undamaged batteries only.
    Adapting to devices
    In order to control your devices you must adapt or
    set the remote control to them. There are two ways
    of doing so: direct control code entry or code
    search.
    If the UR 850 LCD does not understand you it
    displays ERROR and you can then repeat the entry.
    Direct control code entry
    Example: setting the remote control for a Philips TV
    set:
    1. Switch on your device, e.g. the TV, set to any
    station.
    2. To prepare code entry, briefly press the SET
    button in the bottom right corner of the keypad, then
    the required device button, e.g. TV. A brand and a
    code number appear, see diagram.
    – You cannot enter
    a new code if you have activated the code entry lock.
    3. Select the brand of your device, in this
    example Philips, with or . The first available
    code in the device list is displayed.
    4. Press a few buttons to determine whether you
    have found a suitable code. When the code
    corresponds to your device, press OK and the
    setting for this device is completed.
    5. If the code you have found does work at all or
    not properly, try another code by selecting the next
    code for the brand using the or button, then
    test the code as described above under 4. and, if
    successful, confirm with OK.
    6. To set the remote control for other devices,
    proceed in the same way. Instead of the TV device
    button, press another button, e.g. VCR, CBL/SAT
    (DVB-T, DECODER), DVD, TUNER, TAPE, CD,
    AUX).
    -Before setting a code and performing the subsequent test
    for recording or playback devices, please insert a medium
    (tape, CD, cassette, DVD, etc.).- You can interrupt code
    entry at any time by pressing EXIT.
    Code search
    If the brand of your appliance is not in the list or
    none of the codes given fits, we recommend the
    automatic code search.
    Your remote control finds the correct control settings
    almost automatically in a few seconds:
    1. Switch on the device to be controlled. For
    example, a program number appears in the display
    of your satellite receiver.
    2. To start the code search, press and hold the
    SET button for approx. 3 seconds. CODE SETUP
    appears in the display. Confirm this function by
    pressing OK.
    3. DEV SEARCH then appears in the display.
    Confirm this function by pressing OK.
    If DEV
    SEARCH does not appear you can set the function with the
    or button.
    4. Press the device button of the device to be
    controlled, e.g. DVD and confirm the function by
    pressing OK.
    5. Then point the remote control at the device to
    be controlled while the remote control emits a
    different ON/OFF signal every 2 seconds. The
    respective code number is shown in the display.
    6. When your device reacts, press a few buttons
    to determine whether you have found a suitable
    code. If the code corresponds to your device, press
    OK twice. SUCCESS appears in the display, then
    you press the device button, e.g. DVD, to confirm
    the entry. The setting for this device is now
    completed.
    7. If the code you have found does work at all or
    not properly, press EXIT and DEV SEARCH
    appears again. Then proceed again as described
    under 3.
    Please note: - You can reverse the search direction with the
    or button if you have reacted too slowly to a response
    from the device. – The Menu buttons cannot by used for
    testing. - Before setting a code and performing the
    subsequent test for recording or playback devices, please
    insert a medium (tape, CD, cassette, DVD, etc.).- You can
    interrupt code entry at any time by pressing EXIT.
    Other settings
    Setting the time
    1 Press and hold SET for 3 seconds, then set
    CONFIGURE with the or button. Confirm this
    function by pressing OK.
    2 TIME SETUP appears in the display. Confirm
    this function by pressing OK.
    3 Enter the time using the number buttons and
    confirm with the OK button. Then press EXIT
    several times to quit the setting mode.
    Set priority volume control
    With this function you can determine a device
    exclusively for volume control, e.g. your audio
    amplifier. Then the buttons VOL +, VOL and
    always control the amplifier, regardless of which
    device you are controlling.
    1 Press and hold SET for 3 seconds, then set
    CONFIGURE with the or button. Confirm this
    function by pressing OK
    2 TIME SETUP appears in the display. Set VOL
    LOCK with the or button. Confirm this function
    by pressing OK.
    3 Select the device button, e.g. AUX for the
    amplifier and set priority=ON using the or
    button. Confirm this function by pressing OK.
    4 Then press EXIT several times to quit the
    setting mode.
    - You can cancel the priority setting using the same
    procedure. Instead of ON, set OFF for all devices.
Vivanco UR 850 LCD

Ho bisogno di aiuto?

Numero di domande: 0

Hai domande sul Vivanco UR 850 LCD o hai bisogno di aiuto? Fai qui la tua domanda. Fornisci una descrizione chiara e completa del problema e della domanda. Più dettagli fornisci per il tuo problema e la tua domanda, più facile sarà per gli altri proprietari di Vivanco UR 850 LCD rispondere correttamente alla tua domanda.

Consulta qui gratuitamente il manuale per il Vivanco UR 850 LCD. Il manuale rientra nella categoria Telecomando ed è stato valutato da 1 persone con una media di 9. Il manuale è disponibile nelle seguenti lingue: Italiano, Inglese, Tedesco, Spagnolo. Hai domande sul Vivanco UR 850 LCD o hai bisogno di aiuto? Fai la tua domanda qui

Specifiche Vivanco UR 850 LCD

Generale
Marca Vivanco
Modello UR 850 LCD
Prodotto Telecomandi
EAN 4008928188622
Lingua Italiano, Inglese, Tedesco, Spagnolo
Tipo di file PDF
Display
Tipologia display LCD
Batteria
Tipo batteria Mini Stilo AAA
Numero di batterie 2
Contenuto dell'imballo
Batterie incluse

Domande frequenti

Di seguito, troverai le domande più frequenti riguardo Vivanco UR 850 LCD .

La tua domanda non è elencata? Fai la tua domanda qui

ManualeD'uso.it

Stai cercando un manuale? ManualeD'uso.it farà in modo che tu possa trovare il manuale che stai cercando in un attimo. Il nostro database contiene più di 1 milione di manuali in formato PDF di oltre 10.000 marchi. Ogni giorno aggiungiamo i manuali più recenti in modo che sia sempre possibile trovare il prodotto che stai cercando. È molto semplice: basta digitare il marchio e il tipo di prodotto nella barra di ricerca e immediatamente visualizzerai gratuitamente il manuale di tua scelta online.

ManualeD'uso.it

© Copyright 2020 ManualeD'uso.it. Tutti I diritti riservati.

Utilizziamo i cookie per essere sicuri che tu possa avere la migliore esperienza sul nostro sito. Se continui ad utilizzare questo sito noi assumiamo che tu ne sia felice.

Leggi di più